Home Creators Posts Import Register Favorites Logout

Content

An great overall performing energy cell but not quite as good as the BAK 65E and Linkdata 65P. You might not notice the difference though.

For comparisons to other cells like the SA112, RS60, 60XG, F66, and 60P where the numbers are closer, check the Ratings & E-Scores table: https://www.patreon.com/batterymooch/posts/18650-21700-e-138053835

  • The cells I tested did not have the CE or CCC** mark.

  • One vendor calls this cell the 6500D but there’s no mention of that in the datasheet or on Great Power’s web site.

  • This cell looks identical to the Amprius SA112 and performs essentially the same (see graph and photo above). In my opinion Amprius has contracted out manufacturing of their SA112 to Great Power and this is the same cell released in a Great Power wrap.

  • Datasheet rated capacity is 6500mAh (no minimum value). The two cells I tested were 6740mAh and 6755mAh. This is pretty good consistency and well above the rating, as it should be.

  • This cell has a 3.50V nominal voltage. Most “standard” Li-Ion cells are around 3.60.

  • I’m just guessing but this can be due to the addition of silicon to the anode (mixed with the typical graphite) to increase capacity, commonly done now with ultra-high capacity round cells. That tends to lower the nominal voltage of a cell but the particular variation of cathode chemistry can affect that too.

  • Datasheet “recommended discharge current” is 7.5A. “Maximum discharge current” is 12.5A at °0C-35°C. This max value seems reasonable for continuous discharges.

  • There is no max surface temp listed but since the max storage temp is 65°C and the cell reaches about 65°C at 12.5A down to 2.5V I would recommend never letting the cell get above 65°C. Stopping at 60°C or lower would be better for cycle life.

  • Datasheet recommended charge is 3A and max is 4.5A. I recommend staying at 3A or lower to help maintain long cycle life.

  • Only charge when the cell is between 0°C to 45°C. This is a smaller range than most cells (typically up to 60°C).

  • Datasheet AC internal resistance (IR) is <=25mOhms. I measured 18.85mOhms and 18.32mOhms, not good consistency but well below the max spec.

  • DC IR was measured at 24.56mOhms and 23.72mOhms, decent consistency.

  • Datasheet max weight is <=74g. The heaviest cell I tested weighed 71.68g.

  • Datasheet max size is <=21.75mm diameter x <=71.00mm long. The largest cell I tested measured 21.52mm x 70.61mm. A big cell, but that is expected with ultra-high capacity round cells.

  • Datasheet cycle life is at least 500 cycles at +3A/-7.5A down to 2.50V before the cell drops below 80% of original capacity. You can check if Pajda*** is planning on cycle life testing this cell.

  • Like several ultra-high capacity round cells this one seems a bit “delicate”. In my opinion it’s not designed to be treated like a power cell, run at or near its ratings. Run it at around 8A or lower and not when above 45°C or so and you should get good cycle life.

**China Compulsory Certification, additional testing now required for all cells made or sold in China after August 1, 2024. The logo (or “CCC”) and certain information must be put on all cells once they are certified. This typically won’t be done by a manufacturer until the cell is ready to go into full production. A manufacturer can apply for an export-only exemption from CCC testing though if the cells will only be sold outside of China (or for engineering/evaluation samples) so lack of a CCC logo does not guarantee that the cells are pre-production. They could be production-ready cells that were tested and have passed and newer cells will have the new CCC marked wraps.

***Pajda is a highly respected cell tester on the Endless Sphere forums and here on Patreon. He does cycle life testing you will not find anywhere else (and performance testing too).

Files

Comments

No comments found for this post.