Home Creators Posts Import Register Favorites Logout

Poll

What do you charge your “standard” Li-Ion cells to?

  • Over 4.30V, but not an HV cell 2
  • 4.26V- 4.30V 0
  • 4.21V-4.25V 5
  • 4.20V 66
  • 4.15V - 4.19V 19
  • 4.10V - 4.15V 10
  • Below 4.10V 5
  • 2026-11-06
  • 107 votes
{'title': 'What do you charge your “standard” Li-Ion cells to?', 'choices': [{'text': 'Over 4.30V, but not an HV cell', 'votes': 2}, {'text': '4.26V- 4.30V', 'votes': 0}, {'text': '4.21V-4.25V', 'votes': 5}, {'text': '4.20V', 'votes': 66}, {'text': '4.15V - 4.19V', 'votes': 19}, {'text': '4.10V - 4.15V', 'votes': 10}, {'text': 'Below 4.10V', 'votes': 5}], 'closes_at': None, 'created_at': datetime.datetime(2026, 11, 6, 6, 10, 55, tzinfo=datetime.timezone.utc), 'description': None, 'allow_multiple': False, 'total_votes': 107}

Content

After seeing a couple of rather heated online conversations about charging voltage I want to post about going over 4.20V and whether it’s dangerous.

But realized I don’t know what voltage setting most people are using these days. It can certainly change with the application and I’m very curious.

Do you charge to a high voltage to maximize run time? Do you choose a low voltage instead to maximize cycle life?

This is just for “standard” chemistry Li-Ion cells (which includes Li-Po’s). This does not include “HV” cells (which can be charged to 4.30V or even higher).

All the choices below are just for your charger/power supply setting, not the voltage that your cells settle down to after resting a bit. That can vary depending on the charging current, termination current, and cell condition.

Comments

Nils Ljung

If charging an ev battery which normally is not 100% perfectly balanced, I personally like to set the charger to slightly below 4,20v per cell so top cells stops at about 4,20v and the low cells will probably stop at 4,18v.

Andrea

4.18. Just to keep a bit of margin.

Rick

3.6v Vape client

Uwe Ross

4.20 for my daily use 18650s. I also have a few that are dedicated to flashlights that only see occasional use. I try to pull those out of the charger at around 4.1V.

LNXPRO

Li-NMC, i charge to 4.10. There is barely any energy between 4.1 and 4.2 so it's not worth the full cycle stress. I discharge down to 3.4v, again, there is barely any energy left below 3.4v down to 3v to stress the cells. This is for my Leaf battery DIY powerwall that has been running for the past 7 years and so far I have seen almost no degradation in capacity and these are "cycled" every day between 4.1v to 3.4v and back up to 4.1v the next day.

tyler ganze

4.2 but i dont float it, it settles down to 4.15ish off charger

Jayden Blain

I mean the majority of basic chargers don't even give you an option. Defaulting to 4.2. But if I know I won't use 100% capacity. I do like 4.1 to be a little easier on the cells. Like for drones where I won't need the extra ~5% capacity of 4.1 to 4.2v, but the cycle life increases by much more than 5%

Micha Chlst

usually to 4.1V with CV phase. Only if the capacity is really needed up to 4,2V.

arzexa.

Usually charged to 4-4.1V down to 3.4V in lights and power tools if I'm not expecting to work them hard, 4.2V and full capacity otherwise if I need it. Not much point adding extra stress to the cells if I'm not using them to their full potential.

Mircea Tenea

It depends on the application you need. With these latest chemistry tweaks on high energy cells, there's plenty of energy left between 3.4V and 2.8-3.0V. If you're not using it, then no reason to pay extra for this. I'm using 6000+mAh cells in 3p 4p configurations draining no more than 5-6A/cell (12-20A CDR cells), charge them to 4.18V, discharge to 2.9V.

Geoff R.

I generally set my supply to 4.1 to 4.12v and not stress out if I space out and let amps taper to zero at this voltage. I will dial up 4.18v if I want my dumb Daly to 'balance', even though I think it is incapable of this. If I want absolute max range I will dial up 4.20v, but this is rare.

Tyler E

What cells are out there capable of 4.3v safely? Pure curiosity as I am not that informed on charging past 4.2

Battery Mooch

There are a few “HV” pouch cells (LCO chemistry Li-Po’s) that claim 4.30V-4.35V ratings and the science can support that. Cycle life is reduced but it can be done. There are a some specialty round cells that are rated for up to 4.5V but they cost a fortune. I seem to remember a “standard” round cell being cycled at up to 4.5V recently (for short term drone use) but I don’t remember which…from Reliance perhaps? None of the cells being operated at these higher voltage levels have good cycle life though. But they aren’t a lot riskier to use if properly rated and aren’t just standard 4.2V cells with an exaggerated rating to boost sales.