🎸 Monday Magbuddy Drop: Baby Rock N' Roll Trolls! 🎸(Archived) (Patreon)

NOW AVAILABLE ON CULTS 3D HERE: https://cults3d.com/:4676542 ACTIVE MEMBERS GET 50% OFF!

The trolls have been teaching the next generation..and these little rockers are ready to take the stage! 🤘 This month's drop includes both the Baby Rock N' Roll Troll and the XL Baby Rock N' Roll Troll.

🔥 NEW for the XL version!You now have two magnet options:

• Standard version with (3) 2 x 8mm magnets• ULTIMATE STICK Version with (2) 2 x 15mm magnets for maximum holding power. (You could still get away with using only one 15mm magnet)

Don't worry... more original trolls are still being developed. 😊

This is also the beginning of a brand-new Baby Troll line that I've been working on behind the scenes.

Current ideas include:

🌌 Baby Cosmic Troll👨‍🍳 Baby Chef Troll🚀 Baby Space Troll🌱 Baby Garden Troll

These won't all release at once as they're still very much works in progress, but I'd love your feedback.

Which Baby Troll should emerge next?

And one more question:

👉 Do you want every Baby Troll to also have an XL version available?

Drop your thoughts in the comments and help shape the future of the Baby Troll lineup! 🤘💀🎸

Happy printing, Misfits! 💜💙💚🧡💛

👇 DOWNLOADS & PRINT SETTINGS BELOW THIS POINT 👇

🧲Magnet Placement Pause

These prints include a pause for inserting 8×2mm round magnets. Always double check your slicer has a pause. Sometimes settings don't "stick" especially when everyone uses different slicers. We have a tutorial on how to check under Tutorials inside Collections.

🚩8x2mm magnets we use→ https://amzn.to/46b4go9

🚩15x2mm magnets we use: https://amzn.to/4vqZUUw-->If you prefer no magnets, simply delete the pause and let it run through!

Printers Used:Bambu Lab A1, A1 MINI / P1 Series

Snapmaker U1/Creator 5: While we print with these purgeless printers, all files are saved as a Bambu files and individual settings may need to be manually entered for other Orca slicers. Subject to change in the future.

Material: PLA

Filament Used:

Troll Skin: https://amzn.to/43PUNRU

XL Baby Troll Hair: https://amzn.to/4uWtGQ5

Baby Troll Hair: https://amzn.to/4uPTIEA

⚙ Quality

• Layer Height: 0.16mm... (The smaller the layer height, the higher the quality. This is your choice. We use .12 to .16, 99% of the time).

💪 Strength

• Walls: 3• Infill: 10%• Pattern: Gyroid

🚀 Speed

• Outer Wall: 200mm/s• Inner Wall: 200 mm/s• Sparse Infill: 200 mm/s• Internal Solid Fill: 200 mm/s

*Top Surface: 200mm/s (100 if using silk filament); otherwise 150 to 200 is good• Overhang Speeds: 20 / 20 / 20

🌳 Supports

🚨 While we have not had any breaks while removing supports-we took EXTRA precaution around the guitar neck and advise to hold the neck securely while removing supports as they are delicate.

• Type: Tree• Style: Default• Support Angle: 20• On Build Plate Only: Yes-->> Critical for supports to NOT fill your magnet hole• Top Z Distance: 0.24• Bottom Z Distance: 0.24• Base Pattern: Hollow

🔧 Other Settings

• No Brim• Purge into Object Support: No• Flush Multiplier: 1.3x

Print Notes

You may notice small negative cylinders on top of the guitar where the tuning knobs would normally be.

These were intentionally added because the tuning knobs occasionally failed or broke during printing when supports were removed. While we've successfully printed guitars with the knobs intact in the past, the results weren't always consistent across different printers and settings.

If you'd like to print the guitar with the original tuning knobs, you can remove the negative cylinders in your slicer or modeling software at your own discretion. Just keep in mind that your results may vary depending on printer calibration, support settings, and filament choice.

💖 All settings are suggestions.

These are the settings I personally use and recommend to achieve the quality shown in my photos. However, every printer and user is different, so feel free to modify them as needed to best fit your setup and printing preferences.

💬 LicensingThese files include a commercial license for active 3D Misfits patrons. You may print and sell physical items. Redistribution, reselling, or sharing of STL files is strictly prohibited.