Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

The Wombot 3D Printer from Joel Telling (3D Printing Nerd) arrived and I found some time to set it up. I found the X-Axis motor mount had a crack in it and the bed was knocked off its mounts. Joel packed it really well with lots of padding and peanuts but it still found a way to get cracked. I tried Superglue on it but it's not really holding. It's a minor crack so I decided to try out a test print. The wiring is just as Joel described, a spaghetti mess. That will be a challenge.

I heated up the nozzle to remove some filament left inside. I installed a fresh sheet of Buildtak after reinstalling the bed on its rollers. The bed seems a little loose side to side but I couldn't figure out how to fix that. It powered up and I tested the home positions. Everything seemed fine until the auto homing feature tried to set the Z-axis position. It drove the nozzle into the bed and because the nozzle was hot it burned right through the Buildtak.


I then spent about 30 minutes trying to adjust the bed sensor and finally got it close. I then realized I didn't have a Simplify3D profile for it but it was similar enough to the other I3's I've run so I used that profile. The first print was my Chess Pawn. I used some ABS plastic that Joel sent with the printer and let it go. 


Attached is a picture of the Pawn. It seemed to print really good with smooth sides but the top had a ring of extra plastic I can't explain. There were a few spots in the sides that had a small gap of missing plastic and the Pawn base wasn't level so the pawn sits like the leaning tower of pisa.


Overall though, for a broken motor mount and first time printing, it shows the promise the printer has. I'll have to play with it some more to get this figured out. Just wanted to thank Joel for the printer and give you guys a sneak peak.

Files

Previews only

Comments

Joel Telling

Glad it's up and running, man, I feel bad about that crack. Aurimas should have the STL for that and I bet you could get one printed lickity split.

Brandon T

Heya Chuck, here's a link to the S3D factory file I use for my Wombot XL; aside from the bed size, these settings will probably serve you really well. They are mostly S3D settings that Anthony from The Hot End uses/sent me, with a few changes of my own, but they definitely work better than any of my settings did prior to getting Anthony's help, so hoping they help you as well. :) (Of course, since it *is* a smaller bed, and - according to Aurimas, the bed doesn't heat up as fast nor as hot as the XL's bed - these settings might need more work than I expect. ;) ) <a href="https://www.dropbox.com/s/01wb1cn17bmd3n7/Wombot_XL-031516.fff?dl=0" rel="nofollow noopener" target="_blank">https://www.dropbox.com/s/01wb1cn17bmd3n7/Wombot_XL-031516.fff?dl=0</a> Definitely fix the mount; every time a piece has broken on my Wombot, if I didn't fix it immediately the problem would exacerbate itself to total failure extremely quickly. I think it has to do with the design and what parts are printed, but in any case I agree with Joel and suggest re-printing it just to be safe. As for the bed, if it's wiggling it is because the 3 wheels underneath the bed aren't oriented correctly. If you look at them closely, you'll see that, on the metal "nuts" that are touching the bed (so, the ones farthest from the wheels) have an a vertical "indent" on one side of them - that side needs to be rotated so it faces in towards the tracks. Aurimas calls them "eccentrics" - not sure if that's the technical name or just an Aussie thing, but it works :) - and they actually bend the entire leg structure at a slight angle in that direction. So if the bed gets *too* tight, slightly rotate one (or more) away; but start with them all dead-center-inwards, and it should completely remove side-to-side wiggle for you. ...aaaand last but not least, the z-sensor can be a pain to get right, unfortunately, especially if the x-arm and/or bed aren't perfectly level. Definitely check both bed and x-arm with a bubble level, adjust lead screws/couplers and/or bed nuts to get them in-line as much as you can. Also put some lithium grease (or other dry lubricant) inside of the brass bolts that hold the x-arm brackets onto the lead screws - I had to constantly re-level my x-arm until I did that, but since greasing them I only have to re-level the arm infrequently. Beyond that, that sensor is super-finnicky and a very small adjustment can totally mess it up, so barely turn the sensor screw between each Auto Home until it's good. (And, since I kept forgetting which way did what: "turn left if the gap is too loose, turn right if the gap is too tight." It helps prevent the confusion of it being backwards from a screwdriver. :D ) That's a lot, but I hope it helps! I went through a ton of growing pains with my Wombot, about everything that could go wrong did, so on the bright side if you have any issues let me know as I've probably experienced them myself...and as helpful as Aurimas is, his email responses have gotten shorter and shorter and is on Aussie time of course, while I'm in the US and as you can see my responses may be long, but at least they're thorough. ;) Enjoy that machine! It's a beaut!