Home Creators Posts Import Register Favorites Logout

Content

🔅----[ INFO ]----🔅

B747 Sound Pack for MSFS2020

🔅----[ What's inside ]----🔅

PW 4000 Engine sounds

Cockpit & Cabin sounds : TRU , Gyro , Avionic Fans , Power Bus , Controls , Packs

Weather sounds : Rain (Low/High) , Wind

Exterior Env :  L-Gear Roll/Touch , Flaps , Hydraulics , APU

Flaps , Spoilers & Gears Wind Drag noises

Warning sounds : GPWS , Altimeter Calls

🔅----[  New Changes ]----🔅

v1.04 (07/Apr/2026)

Added Configuration for B747 Dreamlifter MSFS2024 Package

Adjusted Engine Startup , Idle & Shutdown noise level

Tweaked Ground Spool and "in-Cruise" engine sounds

v1.03 (31/Oct/2022)

Updated configuration for the Dev Version of Salty Mod

v1.02 (7/May/2022)

....

🔅----[ Notes ]----🔅

🔅----[ Available Links ]----🔅

v1.04

For "Asobo" B747 DreamLifter (MSFS2024) : Download Link

Older Releases :

v1.03

For Salty Dev (0.6)  : Download Link

v1.02

For Salty B747 : Download Link

v1.01

For Asobo B748 : Download Link

Files

Comments

F28 : French28 Pilot

Could u guys make a sound pack for the ini lockeed tristar plz?

Kent Melendez

Hello, are you able to make this work on the Supertanker despite it being different engines?

airifr

Too loud engines sounds, matter of fact everything is too loud now, like all sounds volumes had been upped? And when disconnecting the autopilot, the disconnect sound is heard alright but also the gpws warning came on and impossible to clear, all the way to the gate, had that gpws warning screaming in the flight deck! I put the aircraft in cold and dark state and the gpws was still screaming...

FTSim+

what Gpws exactly ? "Pull Up" ?

airifr

Alright will do

simon747

These are great!! Good mix of cockpit and wingview and front of engine sounds; well done!

airifr

The GPWS warning does stop now, but still come on briefly, is there a way to prevent it from occuring, only the ap disconnect should sound when disconnecting the AP. Also in the real aircraft pressing the Yoke ap disconnect button disconnects the ap then a second press silent the warning, in this PW the first press disconnects the Ap but the warning doesn't continue..by the way the PWs engines in real aircraft roar during taking off power like the RRs or GEs, your sounds only the lower N1 range is heard whistling up to the 100%N1 https://disk.yandex.com/d/4Hg2bOUI1Lu2Yw

Dash8Demon

It did the same for me as well but not on initial approach. It did so on a go-around.

FTSim+

this was caused by the "Salty" configuration , once the Autopilot is disconnected the "Master Warning" make a sound ,

FTSim+

Not sure for now 😪 but will think of a way to fix it

FTSim+

Alright 😁, GE will be next

airifr

We hear the engines whistle even in cruise at FL380 with the PW, the GenX worked better, the engines roar and whistle fading away as we climb and accelerate passed 10,000ft..

Muhammed Abbas

whats the different between this 747 sound mod comparison to other you posted

StianNorway

is this for the normal 747 standard in flight sim?

StianNorway (edited)

Comment edits

2026-09-23 05:00 i cant get it to work bro
2022-01-28 03:15

FTSim+

Yes it works on the Default Asobo B748 or the Salty Mod - "B747PW_Sp" is inside the "Community" folder ? - Did you rename the "sound" folder that is found inside : .…\HLM_Packages\Official\Steam\asobo-aircraft-b7478i\SimObjects\Airplanes\Asobo_B747_8i\ or .…\HLM_Packages\Official\OneStore\asobo-aircraft-b7478i\SimObjects\Airplanes\Asobo_B747_8i\ - Are you using other Mods that have new sounds ?

Christian Remedy Silveira

I did the same process as in the manual, I use mody salty and it doesn't sound, I don't know what's going wrong

Christian Remedy Silveira

I found the problem now, the lines, informed in the manual to delete in the SALTY folder are not the same as 113 to 127 - 1300 and so many are further down, now I enter the cool sound

FTSim+

Yes , the numbers may change on other Salty versions but the Lines stays the same

Christian Remedy Silveira

yes correct, it is that sometimes people can base themselves on what was instructed in the manual exclude lines 113 to 127, people go and do it even if they don't connect to what is written there

FTSim+

i've checked again the "INFO" file and yes !! you're totally correct 👍 , it is was mentioned ".....(Line 113 to 127 )" . 👉The instruction will be edited , Many thanks

Christian Remedy Silveira

cool, just to support the team, sometimes people follow exactly what is written there in the manual, and it may not work

Michael Barsch

I cannot bring it to life :-( I use the Salty mod and followed all the steps in the manual. Now since Salty Mod was seperated from the default Asobo 748i - is there anything different required? All sounds are muted for me right now.

Robbie Wilson

The sound lines that are supposed to be deleted arent even there anymore - they are not the Asobo sound lines - rather Salty's - look at the lines. Dont think this works at all now. I know they are different numbers, but still when you find the sound lines look at them close. Its like they have their own sounds now - maybe yours?

FTSim+

New Version is uploaded for Salty Mod

FTSim+

Try the New Version (v1.02) for Salty Mod

Robbie Wilson

Hopefully what I said made sense and you were able to find it easy - Also - please tell me you are working on sounds for the new Maddog?

FTSim+

Not sure if you're already know but the MSFS MD80 sound Mod was released on 8/Mars

Chris Peoples

Even with the newer version it still doesn’t work with the salty mod.

FTSim+

v1.02 is Tested on Salty v0.5.1 and it works fine ✅ - Make sure to update the "layout.json" after installing the Mod , try using "build.py" tool ( see "HOW TO INSTALL" Step n° 2/ )

Chris Peoples

Ohh okay so I have to be alone the stable version of the salty not the dev version?

FTSim+

😁 Currently updating the Genx for the "Dev" version of Salty B747 then the PW ( should be ready after the Genx is ready by 1 day max )

alexcolka

Hi I'm hearing an abrupt transition sound from idle engine sound to shutdown sound inside cockpit when cutting engines in the default Asobo 747-800 PW4000 engine, is this normal or are you planning to update the sound pack?