Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Downloads

  • 505301485.mp4

Missing 1 video, as this post has not yet been imported.

Content

I've finally started personalizing and printing badges!!

Making the badges is more tedious than anything else, honestly 😅 Because Canva creates a separate file for each page, I have to print them all one at a time instead of just sending one file of all the pages to the printer - but when I get started on the tickets, those are all the same this year, so I can just print a bunch of copies of the one page 🙌

Once they're all printed and I've checked that I've printed all of them, I move those files so I don't forget which ones I've already printed 🫣 And move to the living room to start cutting them all out. Thankfully, I have a paper cutter, which makes the process go by a bit quicker 🙌

And then I put the individual badges in the badge holders, making sure I punch out the centre piece of plastic at the top for the lanyard to hook in later.

Usually I cut out all the badges before putting any in the holders, but for the sake of showing BTS, I did a few early...and in this case I am very glad I did 😅

Here's where I am looooooosing my mind...

The badge holders that I bought are somehow a few millimeters narrower than last time, despite ordering from the same listing 🫠 So when I used the same template as last year to print...I did not anticipate needing to cut off the sides of the badges a bit 🤦‍♀️

Thankfully, for people with longer names that stretch to both edges of the badge, I do still have a few sleeves left over from last year.

But after spending a full minute and a half trying to fit one of the wider badges into one of the new narrower holders, and succeeding – the holder was warped and wouldn't sit flat. So I of course assumed that the probably too-wide badge was causing the warping and attempted to take it out (this was before I had thought to check the old badge holders). This process of course ruined that badge 🫠

So I tossed aside the ripped badge and reminded myself I need to re-orient that one later (I still need to put that in my spreadsheet, but it'll get done, don't worry!). And I went about putting a narrower badge into that holder.

But it was still warped 🙃

I decided that the warping wasn't bad enough to care too much and moved on to the next badge...but the next badge holder was also warped, and much more so.

Keeping in mind that I was doing this yesterday after stream...so I in fact had a meltdown 🫠 I had a cry. I had a smol yell. And I looked at the stack of badge holders and realized the top half of them were all warped.

So I elected to try stacking them the way last year's were stacked in the box and I'm still hoping that at least helps...otherwise I'm going to have to return the three boxes of badge holders/lanyards, order new ones, and just hope they'll be better...which I truly just do not have it in me to do right now 😅🙃

At least the tickets just have to be printed and cut out 😅

Except if I put any up on the merch store as bookmarks again...then I also have to put thick packing tape on both sides...which comes with its own set of difficulties 😂🙈

Really making it easy for myself out here ✌️😎


As a side note entitled unrelated to this post, it occurred to me yesterday that I am absolutely the most burnt out I have ever been in my lifetime...which feels insane given that there was a time I was working 4 jobs and doing my Master's degree while recovering from a concussion relapse and dealing with ovarian cysts 🫠

I took the rest of the day off yesterday, but I don't really have a lot of time I can be taking off right now, so...I don't anticipate being able to do a ton to alleviate the severity of the burnout...just hoping I can figure out the time and resources after the show to go away for a few days and disconnect 🤷‍♀️

The reason I mention this is because I may need a little extra patience for the next two weeks. I'm going to be more easily upset/irritated. I'm going to be lower energy. I'm probably going to continue to post these BTS posts at random unscheduled times (ideally still on the same days at least, for some modicum of consistency). I'm going to forget a lot. I'm going to feel frantic and unprepared. I'm going to be slower with messages/comments – that doesn't mean don't send them! I still usually see them, I just don't have the energy to respond. But they do mean a lot to me ❤️

I'm just going to need patience and understanding. Probably more than usual. Sorry, and thank you 🫂❤️

Comments

DiversifiedChapter

I'm gonna steal one of your lines and say you are loved, you are supported. You are appreciated. I am sorry that the badges are not being nice to you. I could threaten some plastic and tell it to communicate with it's friends about what it saw. What you are doing is so special and you're an incredible person. I will fight you if you do not accept our praises and acknowledgement

waltermellin

Omg KT sorrrry that sounds SO frustrating and so stressful! 😭. Totally valid that you feel so burnt out. I’d 100% would have a meltdown too 😭 sorry kt 🫂 Im not sure if it will help… but would flattening them and heating them up in a safe way help fix the warping? 🤔. Like flattening them and then leaving them in direct sunlight? It’s sometimes how we reset the coil on cables if they get all kinked up at work. Just a thought ^^