Home Creators Posts Import Register Favorites Logout

Downloads

Content

It's 1st December, so it's time for SSR1 Beta!

I have been really unwell for the last week. The SSR1 design has come together very well the last couple of months, as I demonstrated on the last livestream, but unfortuately I just lost nearly all of the time I set aside for finishing up and writing initial assembly notes.

I did promise 1st December though, and thankfully someone invented the expression "Early Access" for just such occasions as this. This should be a very simple build, especially for anyone who has the Alpha version of the design as a reference. The non-printed parts list is more or less identical (apart from the ESP32).

I do have some extra notes, which I will put below. Obviously, my next release will be a much more substantial set of build instructions! In the meantime the #maker-chat channel on the discord server is the best place to ask for help if you get stuck!

(The files are protected with the december password because of an ongoing Patreon security flaw. Check your email. As a $8 or $16 patron you should have received the passwords in your welcome email, but feel free to contact me if you have any trouble finding them. The files are also available on my discord server.)

Assembly notes:

FastenersUse M3x5.7mm heat-set thread inserts (7x) -4x in the case base-2x in the rail cap-1x in the belt tensioner

Use M3x6 countersunk bolts (4x)-4x to mount the drive pulley to the motor-4x to close up the case cover

Use M3x16 bolts (6x)-1x to mount the idler pulley to the belt tensioner-1x to control the belt tension (with M3 washers)-2x to attach the rail cap to the case base-2x to mount the lower motor to the case base

Use M3x10 bolts (2x) to mount upper motor to the case base

Use M2x8 bolts (4x)-2x to clamp the belt on the receiver (with M2 washers)-2x to attach the encoder mount

Use M2x10 bolts (2x) to mount the PCB clamps

Use M2x5 bolts (4x) to mount the SFOC board

Writing connectionsThe SSR1 Beta1 uses a Waveshare ESP32-S3-Zero or equivalent. The pin numbering on this is different to the DevKit v1 used on SSR1 Alpha.

Use a 20v USB-C trigger module for power, connected to the +/- terminals on the SFOC board.

Motor controller connections:ESP32 4 -> SFOC ENESP32 3 -> SFOC IN3ESP32 2 -> SFOC IN2ESP32 1 -> SFOC IN1ESP32 GND -> SFOC GND (don’t forget!)

Encoder (MT6701) connections:ESP32 10 -> MT6701 DIRESP32 12 -> MT6701 SCLESP32 13 -> MT6701 SDAESP32 5v -> MT6701 VCCESP33 GND -> MT6701 GND (can use the spare GND on the SFOC for this!)

There is no hall sensor currently.

Files

Comments

V

"ESP32 Vin -> MT6701 VCC" Where is the 'Vin' pin? can't find on the ESP32-S3-Zero board. Is it the 5V pin beside the GND top left?

Tempest MAx

You are correct. It is the "5v"pin next to the "GND" pin.

_J2_ (edited)

Comment edits

2026-09-14 17:00 Does this fit a standard FL case like your other devices? If not, can we get one that does? Thanks.
2025-01-20 02:32

Tempest MAx

This fits a FeelStroker case, which will take a fleshlight sleeve. I have released a printable FS case in the past.

John

I understand you don't have any plans of directly supporting the standard FL case like your other devices. Thanks for the clarification. A modular mount system might be another idea, allowing people to make other mounts (like a direct FL one) without needing to disassemble the device to do so. This could allow people to use all your devices without needing (or wanting) to swap cases. I hope your health has been improving. Cheers.

Tempest MAx

Thanks. I don't have plans to create an official one, and the main reason is that I consider the FeelStroker case and receiver to be a much safer design for a stroker of this type. I will be sharing the STEP files of the receiver so people can come up with their own receivers if they want to however.

Justin

i would also like to see a fl case holder. i am interested to know what is the safety issue you are concerned about. i have found with the case you released when used with fl sleaves it can compress them to much so not as much space in sleave and motor works harder and gets hotter