Home Creators Posts Import Register Favorites Logout

Content

Sooo, as some of you know, I bought a 2003, manual Mustang with a V6, back in May! I learned to drive it, covered the entire hood/top/trunk with hentai stickers, and decked out the interior with fuzzy seats. Back in July, the throwout bearing broke... literally the day before I was supposed to drive to my drummer's house to record Tallah's new album. This was either a blessing or a curse.

I got home from tour around the end of September, and I started working on the car in early October with my friend Matt. The day he came over... the car would not start because the battery randomly died and would not hold a charge, so we had to go buy a new one. Even though it was brand new, that one did not start either, so we had to jump it, then we got it to my grandpa's house to work on it.

We then spent TWO WEEKS trying to take the exhaust off. All the exhaust nuts and bolts were rusted and seized on, ESPECIALLY this very stubborn one on the driver's side. We went through various tools from p3n3tration fluid, to a breaker bar, to a Sawzall, to a blow torch, to a drill, to extractor sockets, to an impact wrench, and we FINALLY got the damned thing off with a nut-splitter. 

We were delighted about this... but slightly annoyed because the previous owner installed half a custom exhaust, so instead of the two exhaust pipes going from the manifolds and meeting at an X in the center where you would normally be able to remove some clamps and take off the front half of the exhaust, we were stuck with two VERY LONG and awkward exhaust pipes that we could not even fully take out from under the car... because they looped over the rear axel and were welded on that way, so that was extremely annoying to deal with... as they constantly took up space under the car. All we could do was fan them out the sides and work around them. 

Week three, we removed the driveshaft, starter, and shifter—all easy mode. The rust was bad, but leverage alone was enough to get all the bolts off. It felt like smooth sailing... until we got to the transmission bellhousing.

Once again, all the bolts to the bellhousing were rusted and seized on. It took us ANOTHER two weeks to get most of them off, but the top two, which are already extremely awkward and difficult to reach and require ratchet extensions, held strong. Eventually, we gave up and decided to leave the bellhousing on and just take off the gearbox part of the transmission. This is not always an option, but my transmission is a T5, so the two pieces were separated, thank the lord. 

Once again... we managed to get three out of four bolts off, and the last one was seized and rusted on. Out of sheer willpower and godlike strength, Matt managed knock the final bolt loose, we lowered the transmission, and we removed the broken throwout bearing. What a mess that thing was.  We installed the new one, re-installed the transmission, and we called it a night since everything should have been smooth sailing on the way back because I de-rusted, cleaned, and anti-seized all the bolts... boy, were we wrong.

Wednesday, I worked alone, and mostly everything went back in easy... until I realized we neglected to put the wiring harness on the correct sides of the transmission, so I had to undo all the progress I made that day, lower the transmission by myself, put the wires on the correct side, then redo everything again. Ugh.

Thursday, I redid everything I had to undo on Wednesday, then I started having problems with the passenger's side of the exhaust. I am not even sure how we removed it in the first place because the pipe literally cannot connect to the manifold since the transmission bellhousing hugs the passenger's side of the car quite a bit more than the driver's side! The pipe cannot physically reach the manifold because there is not enough space between the bellhousing and the frame... I would have to back the exhaust out, then up to go around that impassable spot, but I cannot back it out since it loops over the axel and has no where else to go!

There must be some perfect angle we accidentally found when we removed the exhaust, but after several failed attempts at finding that angle, I decided to just start the car to see if it would even turn over. First attempt, nothing, not even dash lights. The brand new battery was completely drained from sitting in my trunk for two months. I had my cousin bring her Jeep over and give me a jump, and after ten minutes, the car started—thing was as loud as a motorcycle! I was STOKED. We let it run for another ten minutes, then turned it off, disconnected the jumper cables, and tried to start it on its own... nothing :( 

Tomorrow, the plan is to cut the passenger's side of the exhaust with a Sawzall, reconnect everything, then just clamp the spot where I cut it and call it a day. I will probably need to purchase another new battery, but I have a feeling the car might have some electrical issue that is prematurely nuking these batteries, so THAT is something I need to deal with next. On top of that, the front, driver's side brake caliper is stuck, so I need to deal with that as well xD

Long story short, when I bought this car, I knew it was going to be a project, which is why I bought it, but I did not think it would be THIS BAD. I purchased it for $3,200, then gave the kid another $100 for driving it over an hour to me, since I could not drive a stick shift yet at the time of purchase. Total, I estimate I have put around $3,500 INTO this car—probably around $2,700 in tools, $100 in parts, $300 in hentai stickers, and $200 in decking out the interior. I have officially invested more than the car is even worth, HOWEVER, I think all the experience and knowledge has been worth it, and once the car is finally drivable, I am going to be the coolest cat in Massachusetts. 

I will keep everybody updated with my progress, but that has been my life since October :P Cheers!

Files

Comments

Natalie Forestell

I admit it, I tried to zoom in on the stickers. 😉

MAAAX

"300 in the hentai stickers" find yourself a vocalist who can say that

Hungry Lights

I put all the extras on my laptop and dresser xD

Evan Plennert

Quite the set of stickers on that there Mustang...

Hungry Lights

They used to look better, but I bought cheap clearcoat, so everything turned blue, lol.

Evan Plennert

Vintage hentai stickers. You could spin a good yarn with em.

cory wooton

signed hentai sticker give away when?

Arizona Tooth

We shoulda stickerbombed the trans. That would have taught it a lesson