Home Creators Posts Import Register Favorites Logout

Content

Hello my patrons! Next up on the main channel: I try to fix this broken Commodore 1702 first seen on a recent second channel video. I brought this monitor home knowing it was broken but hoping it would be fun to fix. Well, the monitor had other ideas! The whole experience felt like jumping right into the frying pan.

Thanks for all the support!

Direct link: https://youtu.be/XUq7hV6cZBo

Files

Commodore 1702 repair gone wrong

This 1702 has been sitting off to the side in the basement taunting me with it's blown fuse. What's causing this monitor to not run properly? Let's see if I can figure it out and get this monitor running again. -- Links First 1702 power-up attempt: https://www.youtube.com/watch?v=gFO-GkviipI&t=3716s&pp=0gcJCWMAwfN6Pr3D Support the channel on Patreon: https://www.patreon.com/adriansdigitalbasement My GitHub repository: https://github.com/misterblack1?tab=repositories --- Instructional videos My video on chip removal without damage: https://www.youtube.com/watch?v=XQVjwPsVFd8 --- Music Intro music and other tracks by: Nathan Divino @itsnathandivino

Comments

Jon Guidry

This one looks tough. I’ve repaired several monitors now (not as many as you), and this is the troubleshooting flow I’ve developed so far based on watching you and to keep me sane. (Also watching our group members fix stuff.) I don’t envy the hours this 1702 put you through! 1. Does the isolated supply maintain the specified B+ under a representative load? - No: repair the supply and repeat the test. - Yes: investigate the horizontal output stage. 2. Is the HOT shorted? - Yes: remove it, then check the surrounding circuit before installing another. - No: investigate drive, supply delivery and secondary loads. 3. Are the output-stage components correct and intact? - Check retrace capacitors, damper circuitry, solder joints and connections, yoke compatibility, and the replacement transistor’s suitability if substituting. Correct any fault found. 4. Is the flyback mechanically and electrically OK? - The fractured core would be a major decision point for me. I’d compare matching units under identical measurement conditions and check whether reseating and securing the pieces changes the inductance. - Some change would be expected as unwanted gaps close. If the reading remained unstable or substantially different from a matching good unit, I’d investigate before another full-power test. Good ringing alone wouldn’t clear it for me. 5. During a controlled, current-limited startup, what stress appears first? - Excessive collector voltage > investigate resonance capacitance, connections, switching timing and the flyback. - Excessive current > investigate magnetic faults, yoke or secondary overloads, and drive duration. - Poor turn-off or excessive transistor dissipation > investigate base drive and transistor suitability. - This would need suitably rated voltage and current measurement equipment. 6. Does an intact, matching flyback correct the abnormal behavior? - Yes: strong evidence that the original flyback assembly is responsible. - No: revisit the remaining possibilities before risking another transistor, especially if it's one of the super hard to find ones. For this monitor, I’d prioritize the resonance capacitors and fractured core before another full-power attempt if you ever decide to work on it again. Your inductance and ring comparisons were really useful in that spreadsheet at the end: the repaired transformer still ringing well, while having roughly 21% lower primary inductance. That would keep the core repair high on my suspect list assuming matching flybacks and test settings. The measurement I’d most want next is the HOT’s collector voltage and current during startup. That might distinguish how it’s being overstressed. I can understand deciding to stop after losing more parts, though; this was a stubborn repair. I'd be pulling what's left of my hair out too. LOL

Rudy's Retro Intel

Wow! That was a tuff one. Just remember, parts are good. Thanks for sharing. Very informative

David Hatt

Despite your frustration, that was an enjoyable video to watch from a learning perspective. But I’m guessing that without more HOTs to burn (literally) this is pretty much the end of the road for diagnosing the problem. Otherwise I feel like it would have been a useful exercise to try the good Flyback on the broken board and see if that truly was the cause of the blown HOTs. Maybe it’s a case of it being the Flyback just a bit below spec is enough to blow a HOT that is also a bit below spec?

David Hatt

That’s a very useful checklist. Definitely going to file that one away. Thanks for sharing.

Lobster256

Often we learn more from our failures than our successes.

Matthew Tunstill

As much as I'd love to do CRT repair, I prefer the enjoyment behind a YouTube video! Love your persistence to hunt down the root cause. We sometimes have to learn to fail in the engineering world.

Jon Guidry

I wondered the same thing. The repaired flyback’s primary measured about 21% lower inductance than the working one. Assuming matching units, that could mean a faster current rise, which might be enough to overstress the lower-rated replacement HOT. It’s a plausible combination, though the measurements don’t prove it. A matching good flyback and suitable HOT would be a useful comparison, after checking the retrace capacitors and surrounding circuit.

Marcus Christie

i use 100w light bulb inplace of 1 amp fuse when testing

Adrian's Digital Basement

The final blown flyback was from a 27" TV and was just as well specced as the original. So it's so hard to know. I think I'm done throwing parts at it unless I can somehow come into possession a bunch of HOTs. This monitor isn't worth the carnage as it's so far from a good quality specimen.

Lester Troeckler

Good work Adrian. My guess is that the HV transformer has a shorted Rectifier at the HV output. These transformers have a doubler or tripler built into the body of the transformer. This keeps the size of the transformer down. Since the anode is disconnected, I think the transformer would pass a ring test. I enjoyed the video very much.

Jon Guidry

Thanks for clarifying, Adrian. Totally understand calling it here. This particular monitor has claimed enough parts and time! Still enjoyed the video and learned plenty from watching the process.

Jon Guidry

A bulb-selection chart would be a handy bench reference! Sounds like a useful idea for a future video, even if this particular 1702 has earned its retirement 😄

David Hatt

I concur — new HOTs aren’t growing on trees and that Flyback isn’t to be trusted with any more. There was plenty of learning on this board already and now it can become plenty of spare parts.