Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

Today, after more than 1 year of development, I am finally able to announce my new T250 3D printer. It has been redesigned from the ground up with the needs of speedheads in mind.

Frame

The T100 was designed to handle accelerations up to 100,000mm/s2, with the v1.1 release I was able to improve the frame design to handle more than 150,000mm/s2. But every design has it's limits. With the T250, I started from scratch to design a frame capable of absorbing more than 250,000mm/s2 without bouncing like a broken washing machine and without the need to anchor the printer to a table or wall. Here's a video of the frame in action. It's not anchored and yes it's in realtime: https://www.youtube.com/shorts/6H1LkEzcJpI

Build volume:

It was important to me to keep the size of the gantry. 250mm long rods are the sweet spot for fast, reliable printing. But I know my community's biggest wish was for a larger build volume. So I squeezed every millimeter out of the gantry to get a build volume of 192x212x175mm. That's a 60% increase in build volume over the T100 without adding any weight to the gantry!

Motion System

People building a T100 have been able to print a BSO in an average of 6 minutes. There have also been a handful of people in the community who have been able to push the printer to a 3 minute BSO, which is crazy, but also shows the limitations of a 2-motor motion system. For the T250, I decided to get rid of this limitation by building the printer around a 4-motor CoreXY motion system. 4 motors means 50-60% more acceleration at the same speeds compared to a 2-motor system. Also, since the effective belt length has been halved, prints will have less belt artifacts.

Toolhead

Bowden is cool for fast printing, but it's so hard to tune it, and even then there are artefacts that the pressure advanced can't compensate for. For me, I am looking for maximum performance at the highest quality standard. So I decided to change the extruder to a direct drive approach and build an extruder that overcomes all the problems that other extruders have, since the where build without having a rod based motion system in mind. I knew that to get the most acceleration out of the printer, I had to place the extruder motor at the centre of gravity. I also knew that every millimetre that the hot end moved away from the carriage would cost me acceleration because of the higher shear forces it created. The T250 is based on BMG Extruder gears that are reversed to reduce the distance between the hotend and the carriage, the drive wheel is above the motor to give more space for longer melt zones, and it also incorporates a mounting plate for different hotends as an integral part of the extruder, making it 6g lighter than a Sherpa Mini and reducing the length of the bowden tube between the hotend and the extruder by up to 15mm (vary based on the used hotend) which reduced PA by up to 30%

Hotend: I designed the printer to fit all high flow hotends. Rapido UHF? check! Mosquito Magnum? Check, Goliath Air? Check. Also for those wo are looking forward to use modified hotends, most of the high flow mods of the Rapido should be supported out of the box by since there are 12mm slack distance where magic could happen.

Cooling: The T100's cooling performance was good enough for most prints, so why change? Well, two 5015 fans add about 50 grams of weight to the toolhead, plus they need a long duct to deliver their power, which adds another 20 grams. For the T250, I eliminated that weight by adding CPAP remote part cooling. To further improve cooling performance, I added two side blowers that improve overall cooling and therefore minimum layer times. The cool thing about the blowers is that they are integrated into the frame, which reduces the volume of the printer compared to a traditional build approach where you have to... Speaking of cooling, I also decided to add active motor cooling. This allows you to overdrive the motors to get more torque for a longer period of time. It also reduces downtime between BSO prints by a factor of 3-4. Demo of the cooling: https://www.patreon.com/posts/110303581

Z assembly: One of the most criticised parts of the T100 was the print bed design. So I decided to get rid of it completely and start from scratch. The new bed on the T250 is based on 3 motors that allow automatic Z-tilt bed levelling. I also decided to add a real-time automatic levelling sensor that can measure a grid of 625 points in less than 15 seconds. Speaking of the bed, as the supplier of the Ender 2 Pro bed has been rather unreliable, I have decided to stop supporting it. As an alternative I offer two options: An Ender 3 print bed, which is cheap and available worldwide, and the Prusa 3 mini print bed, which is a bit smaller, more expensive, but much more accurate.

Electronics

The T100 was designed as a 24V printer. As 24V is harmless to the human body it allowed me to design a hot rod based printer where every part could be accessed and changed in seconds rather than minutes or hours. The T250 was designed with 60V in mind. 60V means you have 3 times the headroom on your motors before the voltage they generate kills them. But it also means that we are leaving the area where we no longer have to worry about electrical safety. The T250 comes with an electrical enclosure, an AC power outlet and covers for the power supply connectors. I have tried to make it as safe as possible, but still easy to service. Also, as we're aiming higher, I've decided to use an Orange PI Zero as the Klipper host; compared to the BananaPI it has 3x the CPU power and should therefore be able to handle all the Klipper calculations without desyncing. Also, to cool the whole system, I built an air tunnel inside the electrical case to keep the CPU and TMC drivers cool even during the hardest challenges.

More: I've also added a few cool things that don't improve performance, but add to the style factor! The new belt path no longer blocks the view of the print object. Also to improve the view, I decided to add RGB light strips to the top frame on 3 sides (Demo: https://www.patreon.com/posts/110304267 ) So when you are shooting your prints, there will be no shadows on the print area. Cable management: I decided to make the main parts of the frame hollow so that all the cables could be routed through the printer's frame. So when the printer is assembled, there are only 2 cable runs visible, 1 from the tool head to the CPAP box and 1 from the heating bed to the bottom cover. This gives the printer a tidy appearance. And there is much more, such as clamps for the USB and Ethernet ports, the cubic design that makes it easy to enclose the printer, and many more little things.

As always, this printer design will be released to the public as soon as we have finished all the documentation around the printer, optimised the slicer profiles and also fixed any tolerance issues that might be part of this design. So if you want to build this printer now, I invite you to be part of the alpha phase on Patreon!

Files

Previews only

Comments

Daniel San Pedro

I was feeding my daughter while the wife was getting ready for the day and I spooked them both when I gasped and said “WHAAAAAAT?!? No way!!! Wooo it’s released!”

Felix _

I'm looking forward to build it and asked myself, is it possibile to use the The100 Motion kit? I know you want to make a new motion kit, but i have a The100 Motion kit laying around and was wondering if i can keep it when the rods don't change in the length.

Felix _

Nice, then i purchase some rods from the same supplier and look for those with the best quality xD Any advice how to get good ones like in your kit from Fushi, or is it really just gambling?

JodelJochen

Awsome News. So what is the way to get access to the Alpha files? Wanna get starting asap 😅

The100

The Alpha is part of my $12 premium backer program, If you are able to wait 2-3 month until the printer reaches beta state it will be also available for my $5 backers. I will release a roadmap to the public release in the next days here on patreon

spacebut

I love it. But it will go on the project list for now. But in the near future it for sure a fun project.

The100

No you have to use the Step file. What I would suggest is to color every printed part to in the Step file to keep track

See

I like the purpose of a bowden in the V100 being to keep the tool head light, and have had no issues tuning it. Would the V250 gantry hypothetically be backwards compatible with the V100 toolhead if I modified step files to anchor the bowden motor setup?

Shawn Batista

Do we have an estimate on the amount of filament this will require?