Home Creators Posts Import Register Favorites Logout

Content


For the release of my Assembly Guide Part 4 video, I decided add a step by step guide in article form as goodie for you, so if you prefer to have a text for the installation, here is it!


1. Download Armbian_21.08.1_Bananapim2zero_bullseye_current_5.10.60.img.xz from https://fi.mirror.armbian.de/archive/bananapim2zero/archive/ and Install it with Raspberry Pi Image on the SD Card
2. Insert SD Card in BananaPI and connect it through Micro USB OTG Port to your PC, wait until the red light starts blinking. (should not take longer than 20 sec.)
3. Open Terminal and find the serial usb port of the BananaPI with the command ls /dev/tty.usb** In my case it's /dev/tty.usbmodem2101
4. Open a serial connection with screen /dev/tty.usbmodem2101 1152000
5. set a new root password
6. Set BASH as shell
7. add the user klipper and set its password
8. setup WIFI with nmtui
9. check ip address with /sbin/ifconfig in my case it's 192.168.178.42
10. Disconnect the USB Cable from the OTG Port and connect it to the DC Port
11. After the System booted connect through ssh ssh klipper@192.168.178.42
12. Download kiauh with git clone https://github.com/th33xitus/kiauh.git
13. Start kiauh with ./kiauh/kiauh.sh
14. goto Install menu (1)
15. Install Klipper
16. Choose Python3
17. Set 1 Instance
18. Install Moonraker
19. Install Fluid
20. Set yes for special macros
21. Install numpy dependencies with sudo apt install python3-numpy python3-matplotlib libatlas-base-dev
22. Install numpy with ~/klippy-env/bin/pip3 install -v numpy==1.18
23. wait 20-30min
24. Change dir with cd ~/klipper/
25. Start configure tool with make menuconfig
26. Enable extra low-level configuration options
27. Set Micro-controller Architecture to Raspberry Pi RP2040
28. Set Communication Interface to Serial (on UART0 GPIO1/GPIO0)
29. Build Firmware with make command
30. Unlock SKR Pico Bootload by attaching jumper
31. mount SKR Pico with sudo mount /dev/sda1 /mnt
32. Copy the new Firmware with sudo cp out/klipper.uf2 /mnt
33. Unmount device with sudo umount /mnt
34. Remove bootloader jumper and hit reset button
35. Disconnect USB
36. Open Armbian Config Tool by sudo armbian-config
37. Activate uart3 in System->Hardware
38. Reboot both boards
39. Open Klipper UI
40. Connect to MCU by serial: /dev/ttyS3
41. Set Restart method by restart_method: command

Comments

Sir Mcstoney

Very much appreciated. This will come in mighty handy very soon. Had to order more screws as i didnt order enough so have to wait even though I have top almost together

Borislav

I have no idea if I will be able to follow the steps exactly.. Fingers crossed. :) I'm waiting for hardware to come but I think I will be able to finish the printer in mid June.

James Harrod

need a PC user guide - a lot of the commands are MAC specific

Mike

Hallo ich bin Mike und habe ein Problem das numpy==1.18 zeigt mir ständig einen Fehler ich komme nicht weiter kann mir jemand helfen spreche sehr schlecht englisch

BenOvation

Mike, ich hatte die gleiche Erfahrung, mein Deutsch ist nicht so gut, aber ich werde es versuchen. Folge den Anweisungen unten: For those who read English, I had the same experience, follow the instructions below: cd ~ /.cahce/pip/ mv wheels/ oldwheels ~/klippy-env/bin/pip3 uninstall cython ~/klippy-env/bin/pip3 install cython==0.29.37 ~/klippy-env/bin/pip3 install -v numpy==1.18 --no-cache-dir --no-build-isolation mv oldwheels/ wheels cd ~ ~/kilppy-env/bin/pip3 list Bisher scheint das zu funktionieren. Ich bin gerade dabei, meinen Drucker zu bauen, und hatte noch nicht die Gelegenheit, dies am Drucker selbst zu testen, also benutze es auf eigene Gefahr. Dies hat es mir ermöglicht, NumPy erfolgreich in die Klipper-Umgebung zu installieren. So far, that seems to work. I am in the process of building my printer now and haven't had the chance to test this on the printer itself so use at your own risk. This allowed me to successfully install numpy into the Klipper environment.

Michael Hollingsworth

Hi, the link provided for the ambian archive only has nubers startin at 23. --- and none of them says bulseye. Can you please advise?