Home Creators Posts Import Register Favorites Logout

Content

Hi folks!

Some time ago, I investigated the possibility of making wireless-powered LEDs based on RFID circuitry, but ended up shelving it (and inevitably forgetting about it....!). I was only reminded of it recently after one of the puzzles at the "Midnight Madness" puzzlehunt used an artefact containing LEDs that became magically illuminated when placed on a base station. It's one of those effects that is incredibly simple, but can be surprisingly effective if players are not expecting it, or have not seen it before.

So this is just a quickie tech demonstration video of such wireless inductive LEDs, which you can buy from, e.g. https://www.aliexpress.com/item/1005006812964153.html  . You can attach them to any prop you want (perhaps positioned under a thin acrylic sheet to hide them), and they'll emit a glow when placed near a simple coil transmitter circuit. You can either use them for purely aesthetic effect, or to provide a puzzle solution (revealing a route, highlighting particular letters or elements of a design, giving a colour code sequence, etc. etc.)

I've tried to demonstrate the effect of different transmitter coil sizes, LED coil size, and also LED colour. tl;dr: 5mm Green LEDs, coupled with a 24V 200mm transmitter coil give the best performance, lighting up at a range of about 40cm above the centre of the coil (and still lighting up pretty well when placed off-centre to either side too).

If you'd like to make your own, I also demonstrate using these 2.2mH inductors  wired to a regular red LED out of my parts box. Since the induced circuit is AC, one LED actually only uses half of the available energy - you could wire a second LED in the opposite direction across the inductor and achieve twice the brightness "for free", by consuming the other half of the wave. It may or may not work out cheaper doing that than just buying the ready-made ones off Ali, but it does give you the flexibility to experiment with exact form factor etc. to fit into a specific prop.

Files

Wireless Inductive LEDs

Everything is made better with LEDs, right? They make things sparkly, and can be a useful visual feedback mechanism. Some time ago, I investigated an RFID tag that had a built-in LED which was lit when the tag was read - energised by the electromagnetic field as it was brought close to the RFID reader, as found in Skylanders "Lightcore" figures. However, I found that approach was somewhat flawed, and also unnecessarily complicated when all you wanted was an aesthetic effect, not linked to RFID identification. Fortunately, that's where these wireless LEDs might just help - they're much simpler, passive components that are powered solely by induction from a nearby coil. They're small, cheap, can be embedded in 3D-printed parts, resin, or any other props, and never need to be accessed. They have a range of up to almost 40cm from the transmitter coil, and you can even make your own using simple discrete parts! Subscribe to this channel for more playful technology tutorials, and you can check out all the accompanying resources at https://www.patreon.com/playfultech

Comments

Doug

The timing of this is amazing. I just ordered some of these wireless LED's off Adafruit. They haven't even arrived yet. Thanks!

Olga Saltovsky

So amazing thing! I'm going to order it now and think where I can use it. :) Thank you!

Abi · Lyontree

I'm using these in my escape room props!

Richard Maritzer

Alastair: If you power the coil through an INA219 board, can it detect, or is there enough draw from several LEDs for the INA219 to register that the LEDs are being powered? If so, then then an ESP32 or similar can know when an artifact has been placed or brought near the coil to trigger other things.

Alastair Aitchison

That is a great idea, Richard! Yes, the coil certainly does draw more current when more LEDs are being powered. I'm not sure it's a noticeable enough change to be able to detect a single LED, but with a bunch of them inserted, that definitely seems like something that could be detected. I'll add it to my list of experiments to try :)

L Wo

Hi Alastair, do you know any way to make the brightness higher in general? I'm running it at 24v as instructed but if there's too much ambient light the effect is minimal. I'm sure there's a little bit of legroom to increase the voltage, but I don't want to end up setting the module on fire!

Minter Arnaud

can those light work with induction chargers ?