Home Creators Posts Import Register Favorites Logout

Content

This post contains the additional Patron-only resources to accompany the "I want to hold your hand" human circuit puzzle found here.

The total cost of components used is around $25 (the vast majority of that is for the amplifier), as follows:

---

Arduino Uno or Nano ~£2, from e.g. https://www.ebay.co.uk/itm/16M-5V-Mini-USB-Nano-V3-0-ATmega328-Micro-controller-CH340-For-Arduino-Cable/152860514642

For human circuit

2x 1kΩ resistors

1x 1MΩ resistor

1x 0.1μF capacitor

For MP3 playback

DFPlayer Mini, ~£1.20 from, e.g. https://www.aliexpress.com/item/TF-Card-U-Disk-Mini-MP3-Player-Audio-Voice-Module-For-Arduino-DFPlay-Min-Board/32659645208.html (Tech sheet)

Nobsound Stereo Amp $20, from e.g. https://www.aliexpress.com/item/2016-Lastest-Nobsound-NS-10G-Bluetooth-4-0-Mini-Digital-Amplifier-Stereo-HiFi-Power-Amp-50W/32719095410.html

1x 1N4001 diode

2x 1kΩ resistors 

1x 220uF capacitor

1x 3.5mm audio jack breakout ~$0.50, from e.g. https://www.aliexpress.com/item/1pcs-TRRS-3-5mm-Jack-Breakout-Headphone-Video-MP3-Jack-Professional-module/32693340142.html

3.5mm stereo cable

The Arduino code, wiring diagram, schematic, and Fritzing project can be downloaded from https://drive.google.com/open?id=1Y0EcPIXvzYjhInpNOUK8AAJ_y6TB5Thu

Thankyou for your support, and please do ask if you have any questions! 

Comments

Kate Johnston

Hi Alastair! What a great project! My co-teacher and I are using this with our middle school students. Would you have any ideas for us if we wanted to light LED strips after the hands are held instead of playing a song. Thank you!

Elusive Escape Rooms

Hi Alistair! I need help! When I wire it up just like you have shown, it triggers when I hold just one of the two wires. Any idea what could be wrong?

James Sheahan

Hi. Thanks again for these great tutorials and examples. I'd like to have 2 pairs of terminals which the players must hold hands to connect. While pair A is connected, digital readout A changes to reveal some info. While pair B is connected, digital readout B changes to reveal some info. Combining the info from A and B gives the solution for a lock. (My goal is 4 pairs in total but getting 2 working is the first step.) I have duplicated the circuit in the diagram so there are two pairs of complete sets of the resistors, capactor and terminals. (I have changed the code accordingly). They both connect to the same AREF on my Arduino Uno. It all seems to work (holding the As triggers my A outcome, and holding the B's triggers my B outcome). So far so good. However, I notice that if I hold the A terminal connected to the 2 resistors and the B terminal connected to the ground via the single resistor, the A outcome is triggered (and vice versa). I assume this is because they use the same AREF. Is there a way to prevent this? (I'm new to electronics so not sure what solutions there may be.) (An alternative solution to my problem is to keep the circuit as it is but change my puzzle instead, so there is one single common connector (A which goes to Ground) and players must make chains from A to each of the other connectors (1-4). So they must connect A to 1, A to 2, A to 3, A to 4 to get the 4 pieces of info.) Thanks a lot.

Sven Hurt

Thank you very much for your research and the provided infos. I got two questions if I may: 1.) With just the two resistors and the capacitor on the human circuit side, how vulnerable is the circuit to electrostatic discharges? 2.) What is your experience in regards to distance (resistance) / voltage ratio?

Russell Hardman

Looks like a good one to try. I don’t have any metal rods. Could I just use a metal coat hanger to test it?

Sven Hurt

Hurray! Although I had to leave out some parts that I did not have lying arround, building a demo was pretty straight forward, thanks to your tutorial. Edit: All good, my mistake,...

Russell Hardman

I’m just building this now, there is a 0.1 uf capacitor for the human circuit and from my assortment the smallest i have is 2.2 uf. Is that ok or will I need 0.1?

Brian Shaffer

My reading aren’t dropping when I’m holding the wire only when I connect them to something like the surface of my MacBook. What am I doing wrong here?

Óliver Novelles

Hi, Alastair! First of all, happy new year! Well, I would like to make this project but I want to make sound, depending of the number between 0 and 1023, a diferent kind of sounds. F.e.: between 800 & 700, a cat meow, between 700 & 600 a dog woof, etc. Can you tell me how to do it, please? Thx so much!!

Scott Emigh

Hi Alastair...returning to this oldie but goodie for an upcoming escape room I'm building and I'm struggling to get the circuit to behave properly. I've double and triple checked by wiring, however the readings start out in the 100's (not 1k) and actually climb instead of fall, when I complete the circuit with my hands. Any idea what could cause this behavior?

Remco Dresen

Hi! We used this resources and it works like a charm, but when we put a longer cable, the values will change a lot, from 1024 to 400 and back, etc, while when I use some jumper cables the value stays neatly around 1024. Do I need another resistor or what could be the problem?

Gonzalo Cuevas

Hi, Alastair! I'm experience some trouble with this puzzle. I've done it exactly as it is depicted in the schematics (except that I'm using a UNO). Once the hands are in contact, the puzzle solves, the lock opens and, a couple of seconds later, the arduino resets itself. I have no clue about what could be happening. Any hint will be really appreciated! Regards.