Home Creators Posts Import Register Favorites Logout

Content

Goodness, gracious, great balls of.... lightning? 

In their simplest form, escape room puzzles can be reduced down to a series of inputs and outputs. What makes them interesting puzzles is choosing novel methods for players to interact with those inputs and outputs. For this project, I've created an ER tech puzzle using two new components which I think make for interesting interactions:

As an *input*, I'm using an INA219 current sensor to detect whether a plasma ball is being touched or not - effectively turning the entire globe into a "touch sensor"

For the *output*, I'm using a linear actuator. Unlike a maglock, which is either powered or not powered (i.e. locked or not), an actuator expands or contracts, and can be used to reveal or produce an object or clue which players need to proceed.

As I mention in the video, it's important to consider whether the inputs and outputs of a puzzle are well-suited and "balanced". In this case, both the input and output are continuous, rather than instantaneous. Players must co-ordinate and maintain their touches on all of the balls (I'm using only 2, but you can have up to 16!) simultaneously, while the output is slowly revealed. But, if plasma balls don't fit with the theme of your room, you could substitute them for another momentary input sensor that must be held down by players for a length of time instead. 

Timings

00:00 - 03:24 Introduction and demonstration of using INA219 to detect Plasma Ball touch 

03:25 - 10:51 Demonstration of puzzle components

10:52 - 22:32 Wiring

22:33 - 41:41 Arduino Code

41:42 - 43:04 Wrapup

I'll be putting up the code, wiring diagram, and links to all the resources I used for Patreon donors soon. I hope you enjoy it, and please ask if you have any questions!

Files

Plasma Balls + Arduino Escape Room Puzzle

This video shows how an INA219 current sensor can be used together with an Arduino to detect whether a plasma ball is being touched or not and, as such, making it usable as an input device. To demonstrate, I'll create an escape room puzzle in which players must hold two, or more, plasma balls simultaneously in order to make a linear actuator extend, which provides a key, clue, or other component necessary for players to progress. 00:00 - 03:24 Introduction and demonstration of using INA219 to detect Plasma Ball touch 03:25 - 10:51 Demonstration of puzzle components 10:52 - 22:32 Wiring 22:33 - 41:41 Arduino Code 41:42 - 43:04 Wrapup I demonstrate everything you need in the video itself, but if you'd like to download the Arduino code, wiring diagram, and additional resources, you can get them for this and all my other projects at my Patreon page: https://www.patreon.com/playfultech

Comments

sandu florin

Hello Alastair, first of all thank you for your great work, really apreciate it. I would like to make this puzzle but with two 12 V plasma balls, do you think it will work ? Thank you

Worm

Hi Alastair... I love the puzzle. I think I have most of the parts to try it, however, I have no idea how to get/create a 5v or 12v power supply for them? and how to wire them... I can't see how you're doing it in your puzzle and can't find a link to where you have purchased them from? Thanks... Andrew

Kurt Eulaerts

Hi Alastair, i''m trying to build this one but i seem to have some problems. I can't find out what it is. My 2 readers INA219 are recognized by the system on address 0x40 and 0x44. But i get very strange readings from them. address is is around 5 and address 2 is around 20... input 2 never changes not even when i touch the ball. Input 1 changes even when not touching it from +/3 to +/-6 (hereby some readings when nothis is touched) do you have any idea what could be the problem please?

Kurt Eulaerts

4.99,20.65 4.01,20.65 4.90,20.65 3.88,20.65 3.53,20.65 4.01,20.65 4.38,20.65 4.44,20.65 4.83,20.65 5.44,20.65 5.58,20.65

Kurt Eulaerts

Hello Alastair, thank you for your prompt reply. the hardware looks fine now but my readings are all over the place > the readings of the balls when not toched go from 3 to 7... is there a way to flatten these out? I allready tried 3 differnt power supplies, new INA219 boards, new USB power connectors but the issue remains, don't know what the problem is.... :-( i also changed the float percentage and avarage reading , no luck there. ps bothe channels / balls have the same fluctuations.....Thank you in advance for your assistance... if you want i can send some imges if this explanation is not clear ;-) PS; keep up the very nice work !

Gregory Slossar

This will be a great addition to a current room of mine. I currently have an arduino 8 button puzzle that lights 12 LED's when pressed in the right order. I would like to use this Plasma Ball Puzzle, but would need some code modification. Is this something you can do for an additional cost? Basically, I would like 8 plasma balls to replace the buttons and when each plasma ball is pressed in the correct order I would like the actuator to move a little bit. When the 8 balls are pressed in the correct 12 input sequence the actuator would then be at its longest length where it will press a physical button. I would like to give the players feedback with each incorrect combination the actuator would go back to the beginning. Please let me know if that is possible. Thanks.

Hal Woods

#include "src/INA219/INA219.h" when i try and compile this says no such file or directory. ive tried it on editor online and on the downloaded IDE . Any idea on what I've done wrong? Many Thanks for all your cool mechs!

Hal Woods

Thanks for getting back so quick. The problem was that the new IDE and editor online wouldn't recognize the library folder. You have to add a library.properties file into the root to get it to accept it. I really am enjoying all of your entries and want you to know you are a very gifted teacher. Thank you so very much !

Hal Woods

Sorry to return to this. It appears that on any sketch that uses #include "src/ arduino IDE dislikes it. Can you tell me what platform you are using? It may be more simple if i switch over to it.

Hal Woods

I got it working. Switching to regular IDE helped and placing the folders in the sketch folder not the library folder helped as well. Thank you so much it is very cool puzzle

Teia Powell

I am getting this same error when trying to compile both in the IDE and the web editor...how did you correct this? I added the file to my sketch folder and not the library but this did not seem to work. Any suggestions?

Teia Powell

After some troubleshooting with a very patient Alastair, this project works beautifully and will join the ranks for our escape room halloween party. Thank you for all the great work you do and, of course, for your continued support!

Maxim (edited)

Comment edits

2026-09-07 18:00 Hello, I have a plasma ball with 220V power. Can I use it or somehow redo it?
2019-11-18 12:10

Angi

Hi Alastair, I am working on this project and after a lot of messing around I still can not get the actuator to work the relay light flips back and forth but nothing happens i have witched the code, the wires and the relay but still nothing. I know the actuator works because i put it to power. can you please help

Lori Alden

I'm using this in an escape room themed around Alice in Wonderland. My idea was to have the pipe of the linear actuator represent Alice's neck, which grows longer when both plasma balls are touched. When the neck is fully extended, players can access a locket on Alice's necklace, which has a code inside. There was only one hitch: I tried painting the pipe with a thin coat of flesh-toned spray paint, but the actuator scraped it off. It's still a fantastic element, even though Alice has an aluminum-colored neck.