Home Creators Posts Import Register Favorites Logout

Content

Hello lovely supporters! In this post you'll find links to the super-secret Patreons-only downloads to accompany the "Blow Out" candles puzzle. 

The components I used are:

Arduino Nano - https://www.banggood.com/custlink/KvKDUmhTqI

Arduino Sensor Shield - https://www.banggood.com/custlink/KGKyqDqiMW

Sound Sensor - https://www.banggood.com/custlink/3G3hkvz82d

Serial MP3 Player - https://www.banggood.com/custlink/D33dbzDe61

100W Amplifier - https://www.banggood.com/custlink/mKmdNUHwUw

Maglock - https://www.banggood.com/custlink/m3KRB23LA9

+ some 5mm warm white LEDs and 220Ω resistors (I recommend you get a selection pack - you can never have too many LEDs and resistors!)

You can access a Google drive link to download the code, wiring diagram, and Fritzing project at https://drive.google.com/drive/folders/1CtLivWu0WANjWXokHSyHiymOIgYIgbZh?usp=sharing

After clicking the Google Drive link, I recommend you click on the little down triangle at the top of the screen next to the project title and click "Download", which will download the entire contents in a single archive, which you can then extract on your computer (note that the Arduino code is in a subfolder called "LEDCandle", and that itself contains a subfolder called "src", which has the library for the Serial MP3 Player in it - you will need to keep that structure the same when you compile the code). 

As always, please ask if you have any questions!

Comments

Matthew Johnson

Alastair, do you have the MP3 files you used in this project? I know we can just find our own but curious what yours sound like...

Matthew Johnson

I am getting frustrated with the consistency of the sensitivity of the sound sensors. Sometimes they are super sensitive with just talking turning them off and other times I can blow my hardest and it is wont turn off. I did separate the microphone from the PCB and connect them with about 12" of 18 gauge wire in order to install the mic in a hole at the top of the candle and keep the PCB at the bottom of the candle where I could adjust it. Do you think that wire could be the problem? I was thinking if it was the problem it would always be the problem and not be sporadic but I am at wits end and not sure what to do, it is not reliable enough prop to use in production... advice?

Matthew Johnson

One other question... the MP3 player works great when I plug it into a headset or amplified external speaker but it does not work with a PCB speaker. I assume that the phono plug is only outputing line-level volume and needs to be amplified. Which speaker (or MP3 player) can I use instead that will fit inside a small enclosure?

John Macdonald

Hi Alastair, I am having some trouble getting this code to work. I sent you a direct message in hopes to not blow up the comment section here with the errors. Hopefully you can give me some advice! Thanks!

Steve Baudains

Love it, and thanks for answering my questions in the premiere! Steve, IL&M

RJ Hemy

Could this be moved to a mega and use maybe 5 or 6 candles?

Escape Room

Hi Alastair, do you maybe have the picture of actual breadboard, or the whole project, I'm new to arduino, it would help a lot to know to wire correctly :-). Tnx

Jay Loftis

I have noticed that if only one candle is blown out the puzzle does not reset. Can you suggest a bit of code to force the reset when the puzzle is not completed?

Russell Albright II

Alastair: Trying this puzzle out, and when we have everything very close together, it works well. However the escape room we have this planned for I was going to place a candle in each corner of a 8ft by 12ft room. My plan was to run CAT6 between everything, using RJ45 breakout boxes. But when we do this, the LED on the candle that registers sound stays lit all the time. Do you have any suggestions?