Home Creators Posts Import Register Favorites Logout

Content

Hi folks! 

I'm sure many of you might have come across a "rising pedestal" prop, which can make an impressive finale for a bank heist, art gallery theft, sci-fi, or other themed escape room. Well, here's my take on the design, which is slightly different from those I've seen previously because it actually has the item on display (encased behind "glass"). When the controller is triggered, it activates a relay which extends a linear actuator, causing an internal platform to rise up and allow the gem/key/crown/vial to be lifted up and removed from an access hole in the top panel.

The code itself is trivial - all it does is write LOW/HIGH signals to two GPIO pins attached to a dual relay, so you can easily incorporate this prop as the outcome from any of the previous escape room projects I've built. Instead, in this video I'll focus more on the design and hardware considerations I faced during the build. 

The components I used are:

4xLM8UU bearings ~£7 https://www.amazon.co.uk/sourcing-map-Linear-Bearings-Length/dp/B07H95P2HZ/

4xStainless steel rod ~£10 https://www.ebay.co.uk/itm/272646161855

12V DC Linear Actuator ~£24 https://www.ebay.co.uk/itm/124219350197

Kincony A4 ESP32/Relay Controller ~£20 https://www.aliexpress.com/item/1005002823617497.html

18mm MDF board ~£20 https://www.wickes.co.uk/Wickes-General-Purpose-Medium-Density-Fibreboard-MDF---18-x-606-x-1220mm/p/110511

34x34mm Pine Timber ~£5 https://www.wickes.co.uk/Wickes-Whitewood-PSE-Timber---34-x-34-x-2400mm---Pack-of-4/p/236286

3mm Acrylic sheet ~£15 https://kitronik.co.uk/collections/perspex-acrylic-sheets/products/43185-clear-acrylic-sheet-cast-3mm-x-600mm-x-400mm

I've uploaded the OpenSCAD file I used to create the design, as well as an STL model of that design to a Google Drive link - you can use those if you'd like to see exact dimensions of the parts I used (although, to be honest, there's no particular reason for choosing those exact measurements - I was largely making that up as I went along based on the sizes of bits of wood I had available!). I've also uploaded an STL file of the 3D-printed cap I used to secure the bearings in place for the steel guide rods. And, of course, the Fritzing diagram and Arduino code. You can access all that, here:

https://drive.google.com/drive/folders/1IFOqvxRZjcYPVn89nwxfjJo_YY1iH330?usp=share_link

I've tried to explain my design choices throughout the video, but if you have any comments, questions, or suggestions, please do let me know! And I hope you enjoy :)

Files

Learn to Make Your Own Rising Pedestal Escape Room Prop

In this video I'll demonstrate how to build a "rising pedestal" prop - which can be used as an impressive finale for a bank heist, art gallery, sci-fi, or other themed escape room. A prize item is displayed on a platform of the pedestal, but is completely encased preventing players from accessing it. Instead, they must first solve a puzzle which triggers a relay to supply power to a linear actuator. This causes a rising platform to lift up, exposing the item through an access hole in the top of the pedestal! The pedestal is assembled from MDF and plywood, with four 8mm steel rods and LM8UU bearings. The rising mechanism uses a 12V linear actuator, a dual-channel relay, controlled by an ESP32 (or Arduino/Raspberry Pi/STM32 etc.). The total cost of components and construction is under £100. The pedestal motion is controlled by three simple functions in the code running on the controller: rise(), fall(), and stop(). These can be called from any of the examples I've previously demonstrated on this channel - e.g. based on a button input, a keypad, RFID, Hall sensor, or touch sensor, making it easy to integrate this prop into any sort of puzzle . 00:00:00 - 00:01:01 Introduction and Demonstration 00:01:02 - 00:03:26 Design 00:03:27 - 00:04:32 Physical Construction 00:04:33 - 00:07:07 Rising Platform 00:07:08 - 00:07:57 Electronic Controller 00:07:58 - 00:12:28 Wiring the Linear Actuator 00:12:29 - 00:18:45 Arduino / ESP32 code 00:18:46 - 00:19:56 Wrapup If you enjoyed this video or found it helpful, please like and subscribe to this channel. And, if you'd like to download the resources used in all the escape room projects shown on this channel (and support me to continue making more tutorials in the future!), please check out my Patreon at https://www.patreon.com/playfultech #diy #arduino #escaperoom

Comments

Steve Baudains

Hi Alastair, how did you secure the rods into the "lid"? Are they in such a way as to deter the "gorilla" clients many of us come across? I can see a group trying to jimmy the lid off.

Jessica

This is great!

Katelyn Cahill-Rowley

Thank you! I am actually in the middle of making a rising stalagmite, revealing a geode. I'm wondering how much of the stability in your design is due to the steel rods--mechanically, do you think I can basically just use the bits from the jewel platform down, or will I need something else--like drawer sliders or your steel rods--to keep it from being overly wiggly from side to side? Edit: I think my own answer here is yes, I'll need something like slides or rods.

CymaSpace

Did you go with 1000mm steel rods for your 300mm actuator?

RJ Hemy

I can't find the code in the folder. Did I miss it?

이동진

no code uploaded sad

stefano legnano

Hi Alastair, great as always! If I wanted to turn a mannequin bearing in mind that the greatest weight would be the wooden base that rotates, could you tell me which type of motor I should use? Like force, rpm etc thanks

Nicholas Bicica

Is it possible to use a rfid to trigger the actuator to rise? If so how might I do that?