Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

Hi Folks,


In this video I make the suspension hardware that will support the pendulum. There's a bit of everything in this one; lathe, mill and hand finishing work, as well as some heat bluing of the fasteners.

Enjoy!

Cheers,

Chris.

Files

Previews only

How To Make A Clock In The Home Machine Shop - Part 17 - Making The Regulator And Suspension Post

Making The Regulator And Suspension Post, by Clickspring. In this video I make the suspension hardware that will support the pendulum. There's a bit of everything in this one; lathe, mill and hand finishing work, as well as some heat bluing of the fasteners. If you would like to help support the creation of these videos, then head on over to the Clickspring Patreon page: https://www.patreon.com/clickspring ________________________________________________________ A very special thank you to Patrons Dan Keen, and Rob Shearing. ________________________________________________________ You can also help me make these videos by purchasing via the following Amazon Affiliate links: Cameras used in this video: Panasonic GH5 - https://amzn.to/2rEzhh2 Panasonic X920 - https://amzn.to/2wzxxdT Tools & Shop Products: "Solidworks 2013 Bible": http://amzn.to/2FObS1D Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): http://amzn.to/2HGPaJJ Sherline Lathe: http://amzn.to/2pnXM19 Digital Calipers: https://amzn.to/2IkFh4O YG1 NC Spotting Drill 8% Cobalt HSS 1/8 to 1/2" 120 Degree 5 Pc Set CNC Machine: https://amzn.to/2G7ylv6 Loctite 231097 603 Retaining Compound, 10 mL: http://amzn.to/2pid6vR For more info on this build, as well as other tool making info and plans, visit http://www.clickspringprojects.com Abbreviated Transcript: 00:30 The silk thread catches a hook on the end of the pendulum, and then threads up through the suspension post to the Regulator above. The regulator shaft can be rotated to wind up the thread, which adjust the effective length of the pendulum, and a set screw locks it in place. 01:07 I think the contrasting materials will look excellent together, and given that its quite a tough steel, it should have a greater ability to resist marking and wear than the brass. The regulator shaft needs a small indentation to accommodate the set screw that holds it firm, so I formed that feature first. And with that complete, I formed a dome shape on the other end with a graver. 02:34 I can't know that position until its inserted into the frame, so next I need to mark out and then drill the mounting holes. The hole positions are located relative to the pallet arbor pivot hole, so I'm using the depthing tool to lay out that first position on the centerline of the frames. 03:09 So that's the pallet arbor position marked out, and although I'm not installing the pallet arbor in this video, I do need to accurately transfer this location to the back frame, so that I can use it to as a reference point to mark out the holes that I do need. 04:21 With the positions marked out, the lower hole can be drilled and tapped for the suspension post, and the upper hole drilled and reamed to accept the regulator. The upper surface of the suspension post can now be identified, and the cross holes formed. A quick deburr of the holes, and I can leave these parts as they are for the moment, while I move on to the regulator thumbwheel. 05:08 I made a set of rope knurls and a bump knurling tool holder, and this is one of the parts I had in mind when I made them. A rope knurl is an excellent way to embellish an otherwise simple part, and very easily give it a bit of extra character and class. 06:14 Now I need to clean up that parted off surface, so I'm using a scrap of drill rod as a stub arbor, and fixing the part in place with a spot of super glue. 06:41 releasing the thumbwheel, and then it can be permanently bonded to the regulator post with some Loctite 603. And at this point I decided that a small brass collar would be a useful feature to add to the regulator, to set the depth when its inserted directly, rather than relying on the set screw to pull it in. 08:20 I'm using a piece of brass rod stock to help locate the axis of the hole, and I'm leaving that in place while I drill too, as a bit of extra protection against the drill grabbing as it breaks through into the opening. That hole was then tapped, and the extension marked out so that it could be reduced to its final dimension. 08:53 And I've been keeping the matching extension on the front plate, on the off chance that it might be useful for holding the plates. But I don't think I'll be needing it from here on, so that can come off completely. Both surfaces were brought to the line with the belt sander, and then given a quick finish with abrasive paper. 09:33 to wind onto the regulator post, close to the clock frame. Once the features for the screws were formed, they were hardened, tempered and polished, and then heat blued on a bed of brass chips. 10:35 And that completes all of the components for the pendulum suspension, so lets put them in place and see how they all fit together. References: John Wilding "Large Wheel Skeleton Clock" construction book can be purchased online from Ian T Cobb: http://www.clockmaking-brass.co.uk/clock_construction_books.html Making The Regulator And Suspension Post, by Clickspring.

Comments

Snorburter

Absolutely gorgeous as always Chris!

Al McKague

Very nice as usual! How do you control the temperature when you are bluing the screws so that all of them have such a consistent color?

clickspring

Hey Al, the bluing tray filled with brass chips gives good control of the temperature. Cheers, Chris.

George Harris

Looks great, interesting to see how it all comes together and how it works. Thanks!

Milan Juza

Very nice as always! Thanks Chris. Can't wait for the next video!

John Creasey

Did you have to calculate the size of the knob that you knurled so that it would be an even number of divisions?

AM de Jager

Really cool (as usual). Small request for a future video: Can you make a video where you show your hands while making the different cuts on the lathe (and mill). Having never used a metal lathe before I think it would be quite interesting to see that as well. Thanks!

Paul Busby

This was a nice surprise. I was waiting for part 2 of the hand vice but even better we get a new clock video. Great work as always..

SCOTT SWAALEY

Ahhhh, I feel like an addict getting a much needed fix. Thanks Chris!

Brent Reed

Hah! I am with Scott, a much needed fix indeed! Thanks

Scott Clausen

I can only echo what's written below. This is so great!

clickspring

Hey John, so far I have not needed to worry about diameter calculations, it seems to work for any OD. I find traditional knurling to be quite hit and miss, but this rope knurl is surprisingly quick and easy. Cheers mate :)

clickspring

Cheers Paul! I'm editing part 2 of the hand vise today, so that should be out for you in a few days :)

PJ

Thank you Chris! A beautiful morning, birds singing, bee's buzzing, the last of the "Baby Green" and a Clipspring video... Oh My, food for the soul. Speaking of food, I almost snatched that blued flat head off the screen and popped in my mouth. You've really created an amazing color of blue!! Also appreciated the way you attached that small cable to the silk for a pull...Nice! Squeaks and Giggles and a fine day to you too! ~PJ

Nils Rohwer

Wonderful, love the shots at the end. Love these videos so much.