Wedge Style Hand Vise - Part 2
Wedge Style Hand Vise, Part 2, by Clickspring.
The body of the tool starts to take shape in this 2nd episode of the hand vise build, as I make the threaded insert and the pivot block.
________________________________________________________
A very special thank you to Patrons Dan Keen, and Rob Shearing.
________________________________________________________
Abbreviated Transcript:
00:04 In the previous episode of this hand vise build, I made the handle and the cone shaped section that'll push the jaws together. In this episode I make the main body of the tool, that accepts the jaws, pivot screws and the return springs.
00:35 And you can see that there's some interesting features to be formed for the pivot block, that require a bit of forward planning to get a good result. The central hole needs to be sized for that press fit that I mentioned, and the other features must be well centred on the axis of the part, for the tool to work correctly.
01:58 A quick deburr of the hole, and I can move on with putting in the other features. A wiggler was again used to identify the central axis of the part, and the pivot screw hole positions were drilled all of the way through with the tapping drill size for the screw thread.
02:26 The same positions were then drilled and reamed half of the way through to the correct clearance size for the shouldered section of the pivot screws. Next I used an end mill to carefully mill out the sections that will receive the jaws.
03:08 The holes for the return springs were formed next, using a spot drill to form both holes in the one stroke. Of course drilling into that central hole unavoidable throws up a small burr, so a few twists with the reamer are required to take it off.
04:06 Beyond that it gets a bit hard to muscle the die around the work, and even more so when using tool steel like this, so in this case I don't really have any choice, other than to use the single point method to cut the thread. But before I start making the thread, I do need to do some other preparation. First is the tool itself, which needs to have a 60 degree included angle, as well as the appropriate relief clearance formed.
04:34 A light hone on an oilstone cleans up the small burr left on the top surface by the grinder, and the tool is ready for work. The tool needs to be adjusted in a tool holder to be on center, and the top slide needs to be set to just under 30 degrees.
06:43 The cross slide is returned to the zero position, and then a small cut is put on by winding in the top slide handwheel. With each successive pass, the cut is gradually increased, by continuing to feed in with the top slide, and the process is repeated until the thread is formed to full depth.
07:07 And I should point out that this particular lathe has no threading dial, so unlike those lathes that do have a threading dial, it's essential that the split nut is kept engaged with the lead screw at all times. And I'm keeping my finger positioned right on the stop button. To be sure to catch the tool as it passes into the relief groove at the end of each pass.
07:26 It's surprisingly easy to let the tool run on too far and spoil the work. I'm using this nut as a simple gauge to judge my progress. I know it to be a loose fit on a standard thread, so if it passes on, I know I'm close to the correct minor diameter.
08:19 The end of the thread needs a quick tidy up, so i took care of that next. And if you look closely you can see that I've just nicked the bottom of the clearance groove. It wasn't quite at the correct depth, so that also needs a quick tidy up.
08:51 And with that operation complete, the tailstock support was removed, and the work parted off. OK, so I mentioned that I'll be fixing these 2 parts together with a press fit, and I need some guidance on an appropriate over size dimension for the spigot.
09:07 Machinerys handbook tells me that in this case something like 1 and a half hundredths of a millimeter over the reamed dimension will give me a nice locational interference fit, so that's the dimension that I'm shooting for, over the nominal figure. A light chamfer will help me when it comes to the press fit, and with the outside diameter finalised, I can drill out the center hole.
10:04 And while I'm here, this is my last good opportunity to cleanly access that shoulder section, so now is the time to bring up that surface finish.
10:24 So with most of the features for these parts formed, Its time to press them together, and I'm using this arbor press to do the job. I'm holding the pivot block using a simple drilling vise.
11:43 The belt sander brings the work to the line, and I finished the ends off by using a 400 grit belt end on, to leave a grained finish along the length of the curve. A little time on some abrasive paper puts a similar grained finish on the flat surfaces.
Wedge Style Hand Vise, Part 2, by Clickspring.