How To Make A Clock In The Home Machine Shop - Part 22 - Making The Stopwork Mechanism
Making The Stopwork Mechanism, by Clickspring.
The stopwork is a mechanism designed to protect the clock from overwinding. This particular design also has the added benefit that it can be used to restrict the clock operation to the section of the mainspring with the most constant torque.
If you would like to help support the creation of these videos, then head on over to the Clickspring Patreon page: https://www.patreon.com/clickspring
________________________________________________________
A very special thank you to Patrons Dan Keen, Samuel Irons and Sean Kuyper.
________________________________________________________
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - https://amzn.to/2rEzhh2
Panasonic X920 - https://amzn.to/2wzxxdT
Tools & Shop Products:
"Solidworks 2013 Bible": http://amzn.to/2FObS1D
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): http://amzn.to/2HGPaJJ
Hegner Scroll Saw: https://amzn.to/2IhteVW
Super Pike Saw Blades Size 4/0 pkg of 144: http://amzn.to/2IO6aPw
Blue Matador Abrasive Paper - https://amzn.to/2IAFiBT
Saint Gobain (Norton) - 4 Arkansas Stones + case: http://amzn.to/2HCOAMX
Dormer A190202 Jobber Drill Set, 1.0 mm - 6.0 mm x 0.1 mm Size: https://amzn.to/2DR5fdb
Dormer A190203 Jobber Drill Set, 6.0 mm - 10.0 mm x 0.1 mm Size: https://amzn.to/2ITfeTa
YG1 NC Spotting Drill 8% Cobalt HSS 1/8 to 1/2" 120 Degree 5 Pc Set CNC Machine: https://amzn.to/2G7ylv6
Anytime Tools 5 Lathe Mill CENTER DRILL : https://amzn.to/2IThppO
Norton 1-by-2-by-8-Inch Fine/Coarse India Combination Oilstone, Red: http://amzn.to/2tTEPb0
Abbreviated Transcript:
00:22 The stopwork design used in this clock is essentially a simple counting device. Pinned to the side of the great wheel, it consists of two small wheels, a pivot, and a small friction bow spring. As the barrel arbor rotates with each turn of the winding key, it also turns the stopwork driving wheel.
00:41 The count wheel records each pass of the driving wheel tooth, until the maximum number of desired turns has occurred. At that point the wheels become locked, and no further winding is possible, preventing the clock from being damaged. The barrel arbor requires a slight modification to accept the hexagon shape of the driving wheel.
01:46 I used the scroll saw and belt sander to bring the work closer to the line, taking care to stay clear of that solitary tooth, and then I finished off the perimeter with needle files and abrasive paper.
02:22 In the meantime, I need to determine the optimum depthing for these two wheels, and then mark it out on the great wheel. Which means disassembling the clock for the first time since it was put on test a few weeks ago. And I have to say that the depthing was a bit of a surprise. The interaction when gears are used like this for single tooth movements is very different to a normal tooth engagement.
03:33 The marked position was then drilled and tapped to accept the shouldered pivot. A quick deburr with a hand held countersink and that hole is ready to receive the pivot. The pivot itself is essentially a stud, designed to both locate the count wheel and have sufficient length to be able to accommodate the small friction spring.
07:03 Again marking out the work on the wheel crossing jig this time using a couple of custom turned spacing pins to give the required dimensions. I used some very careful filing to open up that hex hole, and then I gave the wheel a light rub on some abrasive paper to knock down the small filing burr.
09:20 So I've added another size to the punch that I used in the previous episode for the mainspring, to match the required hole in this little spring. A few strokes on an India stone gets the perimeter into shape, and then a quick bend and its done.
10:21 And although not specified in the plans, I decided to make a thin washer to lift the countwheel clear of the great wheel, and so avoid it marking the surface of the wheel over time. OK, so all the bits are good to go, lets put it together and have a better look at how it all works.
10:57 A secondary feature of this stopwork design is that the initial position of the driving wheel can be carefully set to exclude both the first and last few turns of the mainspring, where torque variability is at its worst. It effectively limits operation to the best section of the mainspring, significantly improving the performance of the clock.
11:19 As the clock runs down, the count wheel engages with the driving wheel tooth and reverses its rotation. Until it is once again back in the original position, ready to be rewound.
References:
John Wilding "Large Wheel Skeleton Clock" construction book can be purchased online from Ian T Cobb:
http://www.clockmaking-brass.co.uk/clock_construction_books.html
Making The Stopwork Mechanism, by Clickspring.