Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

Here's next week's video, early for Patrons. 

I'm pretty happy with the results of these compliant legs, despite needing some anti-gravity assistance. Of course there's a massive difference between compliant an rigid legs.

I think we're back to openDog next though, or at least trying to get the same results with a rigid leg and foot sensors.

Files

Previews only

Robot Dog vs Broom - Experiments with Compliant Joints

I've built another three test robot dogs legs in the name of robotic development! I decided to experiment with using current control to make a joint that behaves like a spring, using a brushless motor with 2-stage belt reduction so it's back-driveable, and an ODrive motor controller using current limiting. There are no other joints in this dog because it is only for experimentation, so it cannot walk anywhere, but we can smash the legs into the ground and see what happens. However a robot with springs in it's legs will behave quite unpredictably, so we need to dampen the spring and make it complaint for it to be any use. I experimented with this by using a PID controller to drive the motor to its new position after the 'virtual spring' has stretched. The new test rig seems to work well - it can be shoved around without getting too upset and the legs comply with the ground. ① HARDWARE/SOFTWARE What more important hardware is there in life than the clothes on your back and the cup in your hand. You can get your own Robot X tee or openDog mug at the link below: Teespring: https://teespring.com/stores/james-bruton Below you can also find a lot of the typical tools, equipment and supplies used in my projects. Some of these links are affiliate links, meaning, at no additional cost to you, I might earn a little extra if you click and make a purchase. Lulzbot 3D Printers: http://bit.ly/2Sj6nil Lincoln Electric Welder: https://bit.ly/2Rqhqos CNC Router: https://bit.ly/2QdsNjt Ryobi Tools: http://bit.ly/2RhArcD Axminster Micro Lathe: http://bit.ly/2Sj6eeN 3D Printer Filament: http://bit.ly/2PdcdUu Soldering Iron: http://bit.ly/2DrNWDR Vectric CNC Software: http://bit.ly/2zxpZqv And don't forget the code for some of my projects is available on my GitHub here: https://github.com/xrobots ② GENIUS No MacArthur grant yet. But while I’m still waiting by the phone for that call, maybe you might patronise me with your Patreon-age or pick up some of my merchandise. Or, if you’re all out of digital cash just comment on one of my hilarious Instagram pics, pop me a Tweet or generally yell in my direction. Patreon: https://www.patreon.com/xrobots Teespring: https://teespring.com/stores/james-bruton Instagram: https://www.instagram.com/xrobotsuk Facebook: https://www.facebook.com/xrobots.co.uk Twitter: https://twitter.com/xrobotsuk Huge thanks to my patrons, without whom my standard of living would drastically decline. Like, inside out-Farm Foods bag decline. Plus a very special shoutout to Aleph Objects, Inc who keep me in LulzBot 3D printers and support me via Patreon. Why not join my community, who are mostly made up of actual geniuses. There’s a Facebook group and everything: https://www.facebook.com/pg/xrobots.co.uk/community ③ XROBOTS Former toy designer, current YouTube maker and general robotics, electrical and mechanical engineer, I’m a fan of doing it yourself and innovation by trial and error. My channel is where I share some of my useful and not-so-useful inventions, designs and maker advice. Iron Man is my go-to cosplay, and 3D printing can solve most issues - broken bolts, missing parts, world hunger, you name it. XRobots is the community around my content where you can get in touch, share tips and advice, and more build FAQs, schematics and designs are also available. ④ MUSIC AND SFX The majority of the music and SFX used in my videos is from Epidemic Sound http://share.epidemicsound.com/xrobots

Comments

Anonymous

Interesting stuff. I wonder whether it's true compliance or just active suspension you've created though. As you allude to at the end, true compliance will adjust the leg extension to match the varying terrain, but when you put the block under one leg it seems that the leg still extended fully, albeit with some 'softness' from the virtual spring.

Anonymous

So sonar for each leg to see the ground would be way too complicated?

XRobots

Yes, I'm not sure if the other legs are complying the other way due to the downwards force slightly too. Pretty sure if I had foot switches that removed compliance/dampening from the legs on the ground and the one that hits the ground it would work better, although the natural spring in the legs helps a lot.

XRobots

That could be done, although I'd like a simpler solution of just sensing if the legs are on the ground or not.

Neil Devonshire

Springy dogs operation with full compliance looks similar to how vehicles pitch and roll with the ground, is there anything you can take from the Mcpherson Strut setup (spring and damper settings) on vehicles to apply in your program to springy or open dog? Also. with yours, you can have control of the height of each leg to keep the body parallel (or not) with the ground. So effectively it's like having active suspension with body stabilisation. Liking the deep blue extruded shoulder joints by the way :-)

XRobots

Yes I could fit an IMU and then vary the compliance/dampening to attempt to keep the body level - that only works well if the ground is level though, otherwise we need to average out to the terrain over time or something. Ultimately I think I need a lighter dog with more powerful legs to truly see the effects.

Neil Devonshire

I think we need to make all ground flat lol 😁

XRobots

I'm really thinking about doing more with it... I need to think about that some more.

Logan Vinson

What about variable compliance based on leg position?

XRobots

That would work I suppose, but it really want to be compliant with the ground wherever it is, so it's better for it to 'feel the ground'

Anonymous

Can current sensing not be used to provide a similar feedback to foot switches?

Anonymous

I'm not sure that adding springs to the legs wouldn't work. They just need to be strong enough to offset 'some' of the weight of the dog. Currently the motors are at full load driving against gravity, and zero (/negative/regen?) working with it. The spring would offset 'some' of the gravity and mean the motors would need to work in either direction, but to a lower limit.

XRobots

Current sensing is noisy because it goes up when the motor accelerates anyway.

XRobots

I tried tying bungees to the back of the legs, but I couldn't make them tight enough to have any effect as well as the motor being strong enough to stretch them.

Anonymous

Yeah, you would need to take that into account, but I would expect it to be fairly predictable and you should have all the variables necessary to cancel it out within the control loop. Just a trade-off of control-loop complexity vs physical complexity I guess.

Anonymous

Strange, intuitively it seems to me like they should simply be offsetting gravity forces, although I'd need to do some maths to prove it. Could be the non-linearity/hysteresis of bungees vs springs causing an issue?