Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

I thought Patrons might like to see what I'm going to design next. I've only just stated planning the approximate layout for this one so the CAD is a bit 'blocky' so far. There will be a detailed design / thought process video coming up in a couple of weeks that recaps my R&D to date and describes my reasoning for what comes next. Basic spec is:

-Size is bigger than miniDogs but smaller than openDog V1. Probably similar sized to MIT Cheetah.

-All the motors are in the body or shoulders, with a belt drive to the knee.

-They are brushless motors driven by ODrives, but I'm using the largest diameter & flattest motors that I can reasonably buy. Around 92mm diameter, 25mm thick and 90KV.

-The reduction will be 'Quasi-Direct Drive', which means it's a low ratio reduction that can be back-driven so the motor encoder is also the sensor for external force and the compliance is based on holding power as well as another control loop.

Check out my previous test dogs for more on the last point:  https://www.youtube.com/playlist?list=PLpwJoq86vov9Aogc6PseW8BUe2nQyZESZ 

-Initially I'll just be using a single belt reduction stage at about 5:1 ratio.

-Construction will be similar to miniDog V2 - mostly 3D printed where possible, and aluminium tube for bits that need to be long and/or more rigid. There are always options for further upgrades with carbon fibre etc, and I expect parts will be tested and replaced as I go. I'll be starting with one test leg of course.



Files

Previews only

Comments

Darius Zaerin

i'm so excited, i just love this project! i don't know if its of any use to you, its years old at this point, but i backed a kickstarter campaign for a few of these pi hat boards once without any particular idea of how or what to use them for. https://www.kickstarter.com/projects/shrkey/dark-control-robot-controllers-for-the-raspberry-p/description do you think they could be used for a brushless motor minidog? the ESC board supports 6 motors and can apparently be stacked for many multiples of that. its very low power compared to the odrive obviously, but also very low cost. happy to send you a few if you're interested. i really did appreciate your attempt to keep minidog in a price range that many could build along with without much hesitation and it would be so exciting if this continued to some extent in your next step of development. (i realise that in reality the odrive actually is very budget friendly in its performance class but you know...) anyway also, it may have more 'moving parts' than you'd like but this actually rather simple backdriveable motor reduction might be of interest to you, instead of a pure belt drive. it seems well suited in terms of motion and reduction ratio range and would allow you to use more readily available, higher kv motors. https://www.youtube.com/watch?v=utDagouxM5U&t=557s its also just a fantastic youtube channel, i'm sure you probably know him. not quite as artistically creative as your content but excellent mechanics/electronics and programming stuff. could have colab potential :-)

XRobots

Thanks Daruis, I'm not sure if those boards will be high enough power for most things I do. The issue with a bruhsless motor miniDog is getting low enough KV motors when they are that small - so they'd need a significant amount of reduction. which would make them bulky for something custom made. The main benefit of bruhsless motors for a larger dog is the power we can get from them at low speed, so we don't need so much gear reduction - and then it's all back-drivable to make it compliant.

XRobots

I already subscribe to Skyenfic btw, I was just wanching that video the other day.

Anonymous

The design for v2 is looking like a good successor to v1. Based on your parts list, I am guessing it will weigh around 15-20kg. That would make it about half of v1 (if I remember correctly). I am curious to see how much torque you will be able to generate from those motor modules. What voltage are you planning on running at - 12S/44V?

XRobots

The motors weigh about 400g each, so it's less than 5kg in motors and no ball screws this time, and not much other metal. Hoping it'll be closer to 10kg but we'll see once the rest designed and built. I'll start with 1 test leg to see how the motor power holds up.

XRobots

It'll probably be 24v to start with, possibly moving to 36v - the motors are 44v max and the ODrives I'll be re-using from openDog are 48v max, so I'll probably keep it well under that.