Home Creators Posts Import Register Favorites Logout

Content

It's odd that some of these standard 16mm piezo atomiser disks are sold as being for use at 2.4MHz and some are sold as 110kHz.

The higher frequency is not so easy to generate with a basic microcontroller, but the lower frequency is very easy to create with a simple software loop.

https://www.youtube.com/watch?v=J1ZfOKSkoAc

Files

Scoping out an ultrasonic water atomiser

Although I've featured a few piezo disk water and aroma atomisers in the past - I'm not sure if I've ever scoped one. My main concern was that the act of probing the circuit might damage it by adding rogue capacitance to a resonant circuit. I decided to remove the inductor and replace it with a resistor to get an easy probe connection point for the oscilloscope. In hindsight the weird waveform across the resistor was probably due to the high frequency making the parallel capacitor value significant with the relatively high resistor value compared to the extremely low inductor impedance. The actual drive signal is a near 50/50 110kHz square wave. When I searched for 110kHz along with the keyword piezo I found lots of the same water atomiser disks. This is kinda strange, as some of the disks are sold as operating at 2.4MHz. So I wonder if the lower frequency is just plucking a resonant circuit, where the piezo disk capacitance and inductor form that resonant circuit. On the other hand the 2.4MHz thing might just be an error that has been mass copied by sellers. The inductor is actually a three terminal transformer that has windings that measure as follows:- Primary:- 14uH 0.2m 18-turns (inner winding) Secondary:- 420uH 1.75m 110-turns (outer winding) Both wires around 38 SWG. About 1 ohm per metre. The processor in this circuit is surprisingly stable given the lack of supply decoupling and its switching of a fairly nasty inductive load. But it still manages to bang out a 110kHz square wave while still making time to drive the data output to two addressable LEDs. It's possible it just ditches the piezo drive signal briefly while it's sending out the LED data. It's notable that this circuit doesn't have a capacitor in series between the MOSFET gate and processor drive pin. Many others do that so that if the processor crashes it can't leave the MOSFET turned on continuously, with the risk of high current flow. With a 4MHz clock and 1 million instructions per second processor like a PIC12F629 it's perfectly viable to create the 100kHz square wave with NOP commands as timing packers, allowing for the extra instruction cycle needed for a jump. There are many of these water atomisers available, but if you want this exact one then here's a link to the item on AliExpress (not a sponsor). This is an affiliate link, but that will not affect the price you pay. https://s.click.aliexpress.com/e/_c3nHpFVZ The cost should be around 3 or 4 space-credits. If you enjoy my videos then the easiest way to support the channel is to subscribe for more good video content. But if you would like to contribute a dollar or two for coffee, cookies and gadgets to take apart, you can do so by supporting me on Patreon. I release videos without adverts for critique and feedback on Patreon as soon as they have been made. I also do Patreon live streams, which are much more relaxed and chatty than the busy public ones. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

evilution

Have a look at the jellyfish humidifier. I bought one from Amazon for my Mum for Christmas, tested it out and immediately bought one for myself.

Big Clive

I have pondered those little puffing units. Am I right in saying it just runs a fan in bursts?

Alex Taylor

Leaning the piezoelectric disc vaporized water was a great discovery. A clothing dryer was made by putting a bunch of piezoelectric discs on the drum of the dryer. It was more efficient than even the heatpump dryers. I wonder what kept that from the market

evilution

Yes, it builds up vapour in the main section and then the unit has different patterns for the 5 fans.

Malcolm J Bannister

Wonder if you could put a few drops of essential oil into the water to make a room aroma thingy.

Big Clive

I've not come across the concept of an ultrasonic device for removing water from fabrics. I wonder how the piezo disks would fare.

Big Clive

I'm not sure how well that would work with the wick system. It's common on the open water systems though.

Mike Page

I haven't checked pinning but the 8 pin STM32C0 sells for 27p in tray volume. It would manage both 110kHz and WS2812B drive without breaking a sweat, entirely in the background.

Big Clive

That would involve learning assembler for another range of microcontrollers, of which probably 90% of the code would be ensuring all the unwanted features were disabled.

Alex Taylor

The technology was developed by Oak Ridge National Laboratory (ORNL) and GE Appliances around 2016–2017. Despite prototypes being 5x more energy-efficient and 2x faster they gave up on it because producing the crystals at that scale would be expensive. It sounds like they are using the idea to dry paper pulp and it’s being used on the ISS.

Mike Page

No assembler - C/C++. Much like Arduino. Timing is guaranteed by peripherals not execution times.

Circuitmike

The only thing I don't understand is why the "bottom" of the two sections of the inductor are connected together. I would think it'd work fine with them as two separate, isolated windings. Just a tiny cost-savings measure, maybe (faster to solder 3 wires than 4)?