Home Creators Posts Import Register Favorites Logout

Content

This is ancient, and despite some minor resistor abuse it's still going strong due to being very serviceable.

If I was designing a new one it might just be a simple resistor grid and jump wire though.

https://www.youtube.com/watch?v=ol-B5CQW3zo

Files

Inside my ancient Tandy resistor substitution box

I think I bought this thing about 40 years ago, and it still sees very regular use. I wish they still made them like this, but even with 3D printing and a suitable PCB, it's complicated by the need for sliding contacts. There are 36 resistor values spaced evenly around the PCB, with a matching alignment hole for the spring loaded ball bearing to sit into. Note the two rings of solder-resist to prevent the solder from flowing into the slip ring and contact areas. The resistors start with unusual values at the lower end, with 5, 10, 22, 33, 47, 56 and 100 ohm, but then settle into standard decades based on 10, 15, 22, 33, (47), 56 and 82 all the way up to 1 Megohm, but omitting 470 ohm. presumably to allow a good range of values within the 36 available positions. I think if I was designing something like this now, I might just have an array of resistors and a little flying jumper to select the desired value. Supporting the channel with a dollar or two on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

adrian

I looked for these for a while after seeing them on your channel. Couldn't find them, though if I'd known they were Tandy I'd have had something more specific - but probably not actually available. However I eventually saw a couple on ebay and nabbed them. They were in great condition. I quite like them, even though I have some beautiful Hatfield Instruments boxes. It's so quick and easy to change value with a single dial rather than multiple decade wheels. Jump wire would definitely be a downgrade. I think they might be worth trying to re-create with a 3d printed case and gold-plated PCBs. The sliding contact would be the difficult thing - maybe some gold-plated wire ? Or a contact torn from a relay ?

joe wrench

All I can say is, dont drop them in the bilge water of a boat without taking it apart and cleaning it well.

Mike Page

We've about 4 Sullivan decade boxes from the 1940s to 1960s. All in spec (0.05%) despite some abuse over the years. Beautiful things inside. Need cleaning when the zero ain't zero haha!

Dave Frederick AKA @amorphuc

That is super cool and very handy. I've seen you use it in your videos many times. Thanks for sharing that Big Clive.

Gordo

You've mentioned this handy little unit in the past, time it got its own video. I like that it uses through-hole resistors so you can swap one out if you accidentally cook it. I've a Time thumb-wheel decade box but it's huge, not a toolbox item. Mike (of electric stuff fame) recently showed a very neat looking decade box he got for $15 off Aliexpress, bigger than your Radio Shack unit but much smaller than my Time or those big heavy solid-wood, brass-contact steampunk artefacts from the 40s & 50s. Mike's device uses cheapo speaker terminals (aka BigClive mains safety connectors), but I reckon those could be swapped out for 4mm sockets - I've ordered one so we'll see. I reckon it'll use a pcb bristling with smd resistors, so care will be required in its use..

Gordo

The resistance substitution box from China has arrived. Can't comment on reliability yet but accuracy is very good. I'm not sure that 0.1-10M ohms was a good choice given the speaker terminals and thin internal wiring, the pcb is marked 1-100M ohms. I'll be drililng a hole in the case and installing 2 permanent cables with 4mm plugs using decent wire. These are under £10 off AliExpress, - search WY-RES-01. Maybe buy 2 in case you cook any of the 72 1206 1% smd resistors where your soldering iron can't reach.