Home Creators Posts Import Register Favorites Logout

Content

Once you look past the complete lack of filtering and electrical isolation, this battery charger has some pretty amazing circuitry. Most of the work is done by 6 pins on a dedicated chip, that not only runs the single primary winding transformer, but also uses that same winding to sense secondary voltage and charge state and uses two of those six pins to control the two status LEDs.

https://youtu.be/oxTkqygX5Rc

Files

Impressively empty makita-clone battery charger - with schematic

One of the most commonly cloned battery styles on the online marketplaces is the Makita style. These "Fakita" (Fake Makita) batteries actually contain full charge and discharge protection, which means the tools can be very simple - often just a switch and motor. As supplied, the batteries usually charge via a small jack connector on the pack, but some have an auxiliary charge connection. Those packs can be charged on a slot-in charger like this one. The circuitry in these units is breathtakingly simple. Mainly just a rectifier and smoothing, and a single chip solution that drives the transformer, but also monitors the secondary side by using the primary as a sense coil, and also indicates the state of charge using two directly driven LEDs. The secondary side circuitry is literally just three components. A diode, capacitor and load resistor. The circuit board has indications that it is used for other styles of battery too, as there are legacy connector positions and some obsolete resistor positions that bizarrely still have resistors soldered on them. Note that these chargers are made to Chinese safety standards (none), so always treat the exposed contacts as potentially being a shock risk and don't finger them. I wouldn't recommend using a charger like this with a real Makita battery, as older versions have very little in the way of protection, and with imbalanced cells there is a risk of some being overcharged. The fake packs will terminate the charge as soon as any cell reaches 4.2V. The Fakita batteries vary wildly in capacity, with some being as low as 1Ah, but others being double that. You can buy kits for making your own custom packs using your own choice of cells, and there are some enormous versions with up to 5 cells in parallel (25 cells per pack.) The popularity of these packs means that there is a wide range of unusual accessories available for them, including the very useful work lights with built in USB chargers. You can also get adaptors that allow you to use these packs to power your own equipment. If you want one of these to explore or use then here's a link to the item on AliExpress (not a sponsor). This is an affiliate link, but that will not affect the price you pay. https://s.click.aliexpress.com/e/_c3MNCd93 Alternatively, here's the other version:- https://s.click.aliexpress.com/e/_c44lOBd7 Both should cost between £3 and £5 depending on the yo-yo pricing. Shop around for the best deal. They claim to be universal voltage. I wonder how that goes with the simple resistive dropper power supply for the chip. Especially as it indicates that it uses a classic bipolar transistor. If you enjoy my videos, supporting the channel on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

Andy Hook

I wonder if this could be used to resurrect a dead Makita battery? It would need to be used before the battery is locked out though.

Matt Tester

Interesting you should mention Makita, because my genuine Makita ADP05 USB power supply just offed itself after I connected it to my PDC01 power pack (which holds 4 batteries and uses them in turn) with the LXT dummy battery. I checked the voltage and it's 20V and the correct polarity, it's also fine with my other tools. I can't quite identify the little 3-pin IC package that popped, I can only read the end '53F' of the code but it did let the smell out. I suppose that USB power supply isn't designed for 20V, but there's no indication of that anywhere. Interesting.

Big Clive

If you look on YouTube you will find some amazing science and Arduino software that lets you test Makita batteries, look at their history, and also undo the lockout.

Charles

Fascinating as always, Clive. I love clever designs, but sorry they make extra work for you.

Craig Childs

This is a good example of something you mentioned recently, that schematic is complex and will only appeal to a sub-section of your viewers and will probably lose the attention of a lot of people. Some channels offer a 'skip to' timecode to skip over a portion they know isn't for everyone. I know that means more work in the edit but wondering if it would help prevent an exodus of the non-technical viewers at that point?

Big Clive

My perspective is that viewers can view the test and teardown, and then decide on much more they wish to see.

Circuitmike

That's got to be the weirdest charging circuit I've ever seen! I rewatched the section where you talk about the feedback multiple times but I just don't get why the primary's voltage is somehow mirroring the secondary's, nor how the chip is sensing it. This is one of those circuits I just accept on faith.

James Margarson

HI Clive, have you seen the "Fakita" car jump starters on AliX? There's no mention of voltage regulation on the output, 18-21V into a 12V battery doesn't sound good, although that shouldn't be a problem as the wires with the clips on will probably melt before any other damage is done.

Big Clive

I have one here. I'll test and open it in a video.

Big Clive

It is quite tricky to get your head around. As the magnetic field collapses the energy will be dumped quite quickly through the secondary side diode to the smoothing capacitor and that shunting of the magnetic field is probably the bit that is reflected on the primary side. Although these integrated circuits make the design look simple, they are hiding a lot of complex technology inside.