Home Creators Posts Import Register Favorites Logout

Content

This is not a deep dive. It's just a modular look at the construction and circuitry of a fairly generic import PSU.

https://youtu.be/gkXLnoSLZx0

Files

Quick test and a look inside a generic Hangell 60V 5A power supply

This is not a deep dive video with full reverse engineering. That would be very time consuming and be hampered by much of the functionality being in software. Instead it's a modular look inside the unit to see what sort of separation there is, and the separate sections of the power supply. It is important to select the correct voltage rating on the slide switch at the back of the power supply, to set it for a 120V or 240V supply. Connecting it to 220-240V while set for 120V will damage the unit. The unit has three terminals on the front. Negative, Positive and Earth/Ground. Because this is a high frequency switching power supply, I strongly recommend bridging the negative connection to the earth connection, as it will prevent the capacitively coupled leakage through the compact transformer from causing issues with sensitive components. This style of power supply is rated 300W, although I don't recommend using it at full current for long periods of time. You can get 120V/3A, 60V/5A and 30V/10A units. I chose 60V as it is sometimes useful for testing higher voltage LED panels. A 30V power supply is ample for most workshops. There are two overcurrent modes available. Standard, where the unit limits the output to the set current - and the voltage drops to match (Constant Current mode), and protective mode where overcurrent will instantly shut the output off and sound a warning. The unit is notable for using a TL494 switchmode control chip that is found in many traditional switching supplies. It has a separate power supply for the control circuitry and USB outputs. The control power is managed by a DK124 chip. I'm not a huge fan of the USB sockets being fed from the control circuitry power supply. It poses a risk of interfering with the operation of the control circuitry if high-current or noisy USB loads are plugged in. If you want to explore these units then here's a link to the item on AliExpress (not a sponsor). This is an affiliate link, but that will not affect the price you pay. https://s.click.aliexpress.com/e/_c4beSEit The typical cost of power supplies like this is around £60, which is actually very affordable for lab equipment. For something that is known to comply with local standards you can get power supplies from prominent electronics distributors in your country. In the UK an example of that would be CPC. https://cpc.farnell.com/c/test-equipment/bench-power-supplies-sources-loads The cost will be higher, but you are getting a power supply with safety approval and a warranty. If you enjoy my videos, supporting the channel on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

Uncle Phil

Can't watch this one with my dog nearby. The beep just weirds him out big time. Maybe later on then.

Amro

I've been thinking of getting myself one of these. But I couldn't believe something so cheap was any good.

Mike Hughes

It's currently at £49.03 then there is another £7 off because it's over the £49 threshold, so a bargain for anyone who needs one at £42.03 total with free shipping.

Keith Who

As always, great video on this psu. Interesting to see what’s inside. Do I presume right that there is a thermistor on the heat sink to the op amp mentioned that then in some way switches the fan on? I tend to worry about switch mode noise, when a lot of what I use is RF related. As a result I have two very old analogue power supplies that will do 0-30v at 5 amps and a twin power supplies that has two independent 0-30v at 3 amps. Switch modes do have their place when it comes to high current and a small footprint, but as Clive has shown us in the past, be careful of what you buy.

Mike Hughes

They're good enough for most bench testing procedures, I've had mine for about ten years with no probs, even nickel plating with it, I have a 30v 10A version.

Mike Page

Give me nudge buttons any day over flaky rotary encoders. They always seem to need twiddling several rotations before they behave.

Amro

That's good to know. I wanted them for basically the same reason. I was sceptical about the quality for such a low price. When we got them for the lab they were so expensive! (I'm going back a bit now … lol)

Martin Sowle

I would be interesting to see it under test.

Roy Sigurd Karlsbakk

That 110/220V switch is a bad sign. Most PSUs are autosense these days. That reminds me of when I started working in the mid-ninetees and my first job was with repairing computers. IBM had an Aptiva model that had become particularly popular and in Europe, they had sold out, so they quickly got a separate batch that was in storage in the USA. They shipped it out to shops, and they sold well, but an exceeding number of complaints came in. They had just bought their first computer and the first impression was a loud BANG. All those from the US was set to 110V and someone that could hardly spell PC wasn't really accustomed to checking that switch…

Seán Byrne

I have the older 2 knob 30V 10A model that lacks the OCP button and no USB-C port. It does fine adjustment by pushing in the Voltage or current knob. It has more than paid for itself as an emergency charger during a 5 day power outage from Storm Éowyn. I borrowed a pair of 24V 100Ah LiFePO4 batteries from my brother who has hydropower, temporarily modified my PC's UPS to power our chest freezer, central heating and aquarium filters with one battery and took this power supply to my workplace to recharge the other battery set to 28V 10A, rotating each day during the 5 day power outage.

Dave Frederick AKA @amorphuc

Nice. Thanks Big Clive. I've been looking at some of these for a while now. Maybe it's time to bite the bullet.

Big Clive

It's not uncommon with the higher power units to have the voltage select switch. It makes the PSU more efficient.

Charles

I have one of these - the same 60V 5A version, in fact. When I first got it I had a look at the output to see how noisy it was going to be - there had to be some noise. And there was. It wasn't horrible, but there was a lot of low-level random hash plus very noticeable spikes at the switching frequency. There's a fair bit of empty space in the case, so I made an additional output filter - just a 10mH common-mode choke sandwiched between two 1 uF X2 capacitors and put it in line with the output terminals. Looking at the output after that, it was much better. The low-level random stuff was just gone, and the switching spikes were a lot smaller. The RMS value of the noise, according to an 8-bit scope, was now just barely under 1 mV, which is definitely good enough for my purposes. Dunno if it will last, but I liked the look of the insides.

Paul Hill

I've been looking for a new bench power supply. My old linear supply is playing up. It only goes to 20v (30v supply) but worryingly when I short the leads to set the max current it jumps up to 9+ amps. Sparky & toasty.

Big Clive

The thermistor may be triggering the fan independently via an LM358 op-amp.