Home Creators Posts Import Register Favorites Logout

Content

This has taken a while to perfect, and has been a harsh lesson about the incompatibility between platinum cured silicone and UV cured resin. They do not play well together.

But the end result is very good.

https://www.youtube.com/watch?v=5yNYqsbBkJM

Files

Making a laser lumia/aura effects disk - with a slight silicone disaster

The Lumia or Aura effect is created by shining a laser through rippled glass, but it can be difficult to find the right glass, and someone who can cut a circle from it for you. This was an experiment to use a standard filament based 3D printer to create a silicone mould for optically clear resin. This was my first attempt at creating a mould with liquid silicone. Apparently platinum-cured silicone is very fussy about what it's used with, and my master shape was fine on its own, but when pre-textured with UV cured resin it prevented the silicone from curing in that area and caused an outgassing effect. Even with ordinary two-part resin the silicone still stayed slightly sticky where it was in contact. In the end the answer was to use the 3D printed PLA mould on its own and add the effects onto the cast resin disks afterwards. When using UV curing resin I strongly recommend wearing gloves to protect your hands from contact with it. The chemicals used to make it light sensitive can also make your skin sensitive to sunlight. This is an experimental device. I don't know how the resin will hold up to specific wavelengths of laser energy. It's also probably limited to low power lasers for safety. The disk can also be used with various styles of LEDs for an aurora borealis effect. For laser use the disk should rotate very slowly to get the best optical warping effects. Here's the OpenSCAD script that creates your custom mould for this project. There are two adjustable variables - one for the outer diameter of the disk and one for the central hub where it attaches to a suitable motor. The script will automatically place a small central indent for aligning a drill if needed. OpenSCAD can be downloaded for Windows, Linux and Mac (plus others) from the official site:- https://openscad.org/ To use the script, copy and paste it into the left hand "editor" window in openscad. You can either adjust the two variables directly in the script or you can enable the customizer that will open a window to do it. If you want to use the customizer then you can open it from the "window" drop down menu. To see the results of any changes quickly, press the cube-button with two arrows on it. To do the full build press the cube-button with the hourglass on it, and when it is complete, save the file by pressing the STL button. That will save a design file that can be used in your choice of slicer for 3D printing. The script is below:- //Ripple disk mould maker //Diameter of disk in mm dia=75; //Diameter of central hub in mm hub=20; difference(){ cylinder(h=12,d=dia+12); translate([0,0,1]) cylinder(h=12,d=dia+10); } difference(){ union(){ cylinder(h=5,d=dia); cylinder(h=7,d=hub); } //Central drilling indent translate([0,0,5.5]) cylinder(h=2,d1=0,d2=3); } $fn=100;

Comments

Big Clive

Yes, but less sought after by the Ferengi.

Craig Childs

Another method which would work but not sure how it would be achieved in SCAD (never used it). Create the mould with the lenses in the design software, this has the benefit of being able to create custom shapes, not just convex blobs. Print in ABS resin and smooth the print with acetone vapour. This should create a moukd ready for silicone without the need for any extra steps. Pros: fewer steps and more pattern control. Cons: each lens from the mould would be identical and this method is untested.

Big Clive

Technically speaking I could use a randomiser to cover a surface in random diameter spheres and then subtract a plane below the panel. But I'm not sure it would give good optical clarity unless 3D printed in a clear liquid resin.

Craig Childs

The acetone vapoured ABS leaves a glass like finish, it's quite effective if done well.

Zeedijk Mike

Talking about 3D printing and silicone molding. You should have a look at "soiboi soft" channel. He's making some pritty amazing robot walkers and even a 7 segment display using vacuum, valves and an Arduino for control. The process he is using looks very doable, so no special equipment needed (unless you consider a 3D printer special equipment of course)