Home Creators Posts Import Register Favorites Logout

Content

Normally when things are described as 100W I assume it's going to be something terrible like 10 or 20W, but in this case it's not too bad at 40W per colour, and 80W total.

The circuitry is sensible and the light could actually be worth getting for the PCB on its own for some custom LED projects.

Reassuringly, it appears that you can get replacement LEDs for it from AliExpress.

https://www.youtube.com/watch?v=Cu86wqUd7mc

Files

Cheap LED PAR can test and teardown

There is one obvious issue with this unit, the fan needs more space between it and the power supply to improve airflow. Other than that, this unit is quite well built. As always, the power supply does pose a risk if it does not have good electrical separation in its transformer. I haven't torn the power supply in this light apart (yet). This is a dual colour warm-white and cold-white unit that can create a wide range of colour temperatures. It can be set locally or controlled via a DMX network. Biggest surprise was discovering that this fixture responds to RDM (Remote Device Management), a bidirectional communication protocol that allows lighting fixtures on a network to identify themselves, show their location on request (by lighting and/or moving) and then accept remote configuration of their main setup parameters and their DMX address. This means that you can set up a long run of lights remotely. This unit seems to use a standard two colour 100W LED with each section configured as 100 LED chips in a 10 by 10 array. I tested the power as 40W per colour and 80 W total. Much higher than I was expecting. The control module has potential for use in other projects. It is based on an ARM Cortex processor with what seems to be increasingly refined software. The unit should be able to accommodate a wide input voltage range and can have the current sense resistors adjusted to adapt it to driving other LEDs. The best way to access the unit is to remove the bracket/stand and split the two halves (two hex screws) and then remove the two screws at each end that attach onto one of the halves. That way the side can be lifted off for easy access. This came from AliExpress as a Leleght 100w cob par light. But unfortunately the link is now dead. It cost an unusually low £22 shipped from a UK warehouse. It's worth mentioning that this type of light is often called a PARcan after the type of light it emulates - namely a Parabolic Aluminised Reflector lamp. The original tungsten PARcans are very power hungry, with the PAR64 usually being rated 1000W. If you enjoy my videos, supporting the channel on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

Big Clive

Yo-yo pricing. This one was about £25 shipped in the UK.

Mike Hughes

Could be useful for schools or small Am-dram groups on a limited budget.

Caleb

I am absolutely loving all these lighting videos. I do small community/school theater stuff, where the answer to "what's the budget?" is to laugh hysterically, and these kinds of fixtures are finally becoming affordable for me to play around with. I am truly amazed that so many turn out to support RDM, so far I've never seen that outside of the name brand gear. It really is a lifesaver, I'm so glad I specifically said RDM was a requirement when we ripped out 26kW of incandescent border lights and replaced with 2kW of LED, I am *not* climbing a 15ft ladder to program every single light lol

Big Clive

You do have to consider the safety aspect with this stuff though. They don't take power supply separation seriously.

Caleb

Oh yeah of course, the few I've got or are planning are my personal collection. I do refuse to connect them to the expensive console or place them where the 40 year old teenager is gonna keep poking it out of boredom

Stuart Fisher

If you use a decent DMX splitter it should have opto-isolation which will protect the lighting desk from voltage being sent back down the DMX line. To be honest, this is often a good idea even when using equipment from more mainline brands. The (I'm assuming) lack of genuine safety certification would prevent it being used in a lot of venues.

Caleb

This is one plan I have, tho I'm also tempted to go the cheaper route and use an old raspberry pi and cheap dmx dongle to make my own ACN to DMX node, since I typically do network distribution anyway. Haven't looked into the software side of that yet, but it should be possible with OLA and python (plus a fun little project). As for safety, that's the double edged sword of tiny venues and community theater: no one checks for certifications, which is nice if you know what you're doing and are aware of the risks. But that also means I see so much other stuff that's way worse. I sadly have a reputation as the "no" guy because I flag so many basic safety concerns. The school whose stage we use loves me though, since I mostly keep the insurance company off their backs

Dave Frederick AKA @amorphuc

Thanks Big Clive. At first I was wondering why so many screws on the front of the thing but we see why as you take it to bits! Looks like a 78L05 rather than a 70L05. Not sure if there's a difference?