Home Creators Posts Import Register Favorites Logout

Content

I've been drawing a blank on the chip marked XF E1. Any thoughts?

This PCB is a bluetooth vehicle battery monitor. The CH582F is the bluetooth variant of a standard microcontroller.

Files

Comments

TopEndSpoonie

When I uploaded the PCB to gemini, it came back with "What it does: It acts as a combination of a Power Amplifier (PA) for transmitting further and a Low Noise Amplifier (LNA) for receiving weaker signals from far away." I am sure that you tried that though.

Dave Frederick AKA @amorphuc

So sorry BC. Absolutely no clue here but I must say, I'm no go to with much of this stuff. Sorry Big Clive.

Kevin Baker

eXtra Funky - Enhancement #1

Ian Cockett

Pasted image into Claude Desktop and asked what it was. Then followed up with context that this is a battery monitor. Package: SOIC-8 (Small Outline IC, 8-pin) — the standard narrow-body SOIC with 4 pins on each side, 1.27mm pitch. Device marking: L3 / E1 / XF Decoding the markings: XF is likely the manufacturer code or date/lot code L3 / E1 is the device code This marking pattern strongly suggests it is an XL1509 or similar — but most likely a MOSFET driver or DC-DC controller from a Chinese fab. The "XF" prefix is commonly associated with Xinluda / XINFA or similar Chinese semiconductor houses. However, "L3 E1" in this style is a well-known short-code for the EL3 / L3 series. Cross-referencing SOIC-8 + green PCB context + this marking: Most probable ID: XL1509-ADJ or ME4057 (battery charger) — but the strongest match for L3 on an SOIC-8 from a Chinese vendor is: Most likely: L3 = AO3400-equivalent or a buck controller To get a definitive ID, I'd recommend: Checking the PCB context (what is this board from?) Searching the marking on smd.yooneed.one or ic-lookup.com The dot (•) next to pin 1 confirms standard SOIC-8 orientation Could you share what device/product this PCB is from? That would help narrow it down significantly.You said: This PCB is a bluetooth vehicle battery monitorThis PCB is a bluetooth vehicle battery monitor09:23Claude responded: Great context!Great context! That narrows it down considerably.Searched the webSearched the webThe "XF" code isn't in the SOIC-8 category in the SMD database (it only covers smaller packages like SOD/SOT), and the marking pattern here is different — the XF is likely a date/lot or fab code, not the device ID. Let me re-examine the marking more carefully. Looking at the image again: the three lines read L3 / E1 / XF with a pin-1 dot. Re-reading it rotated 180°, it could alternatively be XT / IE / ɛ7 — but the most likely interpretation remains L3/E1/XF. Here's a consolidated assessment based on the context (Bluetooth car battery monitor) and the marking: Package SOIC-8 (narrow body, 3.9mm wide, 1.27mm pitch, 4 pins per side) — confirmed from the image. Device Identity The most probable candidate for this marking on a Bluetooth vehicle battery monitor is an 8-bit op-amp or precision voltage reference/LDO used for the analog front-end measuring the 12V car battery voltage before feeding an ADC. LineInterpretationL3Device code (part ID abbreviation)E1Grade/version or sub-codeXFDate/lot code or fab mark Best match: LM358 (dual op-amp, SOIC-8) from a Chinese manufacturer, with L3 being a vendor-specific short code for it. Some Chinese fabs (e.g. LXHL, Lux Semiconductors) mark LM358 clones as L3xx. In a battery monitor, a dual op-amp like the LM358 would be used as a signal conditioning or voltage divider buffer stage feeding the BLE SoC's ADC. Alternative candidates: TP4056 clone — unlikely (that's a charger, not a monitor) LM321/LM358 variant from a Chinese house with internal marking L3 Precision shunt reference (e.g. TL431 equivalent in SOIC-8, though that's usually SOT-23) Recommendation To confirm definitively: Trace the pins — if pins 1 & 2 are inputs to an amplifier and pin 8 is V+, it's an op-amp Measure the supply voltage on the chip (likely 3.3V regulated) Search for the specific BT battery monitor brand/model — the schematic or BOM is often posted on teardown forums Would you like help tracing the circuit or identifying other components on the board?

Jon (0ryn) Westgate

I was going to say that it looks from the PCB like a number of the connections look like they are going to the connector. Do you have the pin out of the connections?

Big Clive

The connector data pins are all going to the microcontroller.

Jon (0ryn) Westgate

12 pins is an odd package too. I guess reverse engineer it and see what fits into the 12pin gap.

Ulf Zimmermann

The packaging looks like a 12 pin QFN, From the looks of it pin 1 is connected to general purpose IO pin on the microcontroller. BC, what are the other pins connected to?

Jon (0ryn) Westgate

My gut says it's an EPROM but it's the wrong package. Eproms are usually 8pins not 12

Simon Allen

Could it be an accelerometer? Gemini thinks it is. A square 12-pin integrated circuit with a 4-2-4-2 pin layout (four pins on the top and bottom, two pins on the left and right) is the highly distinctive signature of an LGA-12 (Land Grid Array) package, typically measuring exactly 2mm x 2mm. Given that it is marked "XF" (with E1 being the factory lot/date code) and is sitting on a Bluetooth vehicle battery monitor, this is almost certainly a MEMS Accelerometer—most likely from the Bosch BMA series (such as the BMA253, BMA400, or a direct clone). Why is an accelerometer on a battery monitor? Modern Bluetooth battery monitors (like the popular BM6 models) feature a "Trip Tracking" function. Instead of relying purely on voltage fluctuations to guess when the car is running, they use this tiny accelerometer to detect the physical vibration of the engine starting and the vehicle moving. This allows the monitor to accurately log trip start/stop times and wake the Bluetooth module from sleep mode to save battery. Manuals.plus Standard Bosch LGA-12 Pinout Because this 4-2-4-2 footprint is an industry standard for these specific accelerometers, they almost universally share the following pinout. (Note: Pin 1 is usually indicated by a small dot or a chamfered edge on the top casing). Pin Name Typical Function in a Battery Monitor 1 SDO SPI Data Out / I2C Address Select (Usually tied to GND for I2C) 2 SDx Serial Data (SDA for I2C communication to the main processor) 3 VDDIO Digital I/O Supply Voltage (Usually 1.8V to 3.3V) 4 NC Do Not Connect 5 INT1 Interrupt 1 (Often used to wake the processor when vibration is felt) 6 INT2 Interrupt 2 7 VDD Main Analog Power Supply (Usually 1.8V to 3.3V) 8 GNDIO Ground for I/O 9 GND Main Ground 10 CSB Chip Select (Tied to VDDIO to enable I2C mode) 11 PS Protocol Select (Tied to GND to select I2C instead of SPI) 12 SCx Serial Clock (SCL for I2C communication) The Schematic Application In the context of your battery monitor's schematic, this IC is wired as a peripheral to the main Bluetooth microcontroller (usually an ESP, Nordic, or Beken chip). It receives a clean, stepped-down 3.3V on Pins 3 and 7. It communicates with the main microcontroller via I2C on Pins 2 (SDA) and 12 (SCL). Pin 5 (INT1) will have a dedicated trace running to a "wake" pin on the microcontroller, sending a voltage spike the moment engine vibration is detected. If this chip has failed or burnt out, the battery monitor will likely still read voltage, but the "trip logging" feature in your app will stop working entirely.

Tomáš Kováčik

pin10 of CH582F is SCL (or other serial) so my bet would be eeprom

Stephen Tall

Looks like it's an I2C EEPROM, but with 32kb of data EEPROM on the microcontroller I'm sure why it would be needed.

Electronics.Rocks

I would agree it is storage for credentials of wireless communications, calibration & other registers. As not enough other parts for accelerometer or gyro.

Bwack

I was thinking accellerometer, since it has so little peripheral connection, if any other than I2C, but eeprom seems likely.

The Black Chamber

Google AI says: "On a Bluetooth vehicle battery monitor (such as the widely used BM2, BM3, Ancel, or Antigravity modules), an IC marked "XF" with a tracking or lot number like "31" serves a highly specific role. Because these monitors hook directly up to a 12V car battery (which fluctuates anywhere from 11.5V up to 14.8V while the alternator is charging), the sensitive Bluetooth microcontroller inside cannot run directly off that raw power. The XF IC is almost always one of two things: 1. High-Voltage LDO (Low Dropout Regulator) The most likely candidate is an ultra-low quiescent current, high-input-voltage LDO regulator designed to drop the 12V–15V battery power down to a stable 3.3V or 3.0V to power the onboard Bluetooth transceiver (like an nRF51/nRF52 series chip). Why it fits: Bluetooth battery monitors must draw virtually zero current while the car sits idle (typically < 2mA) so they do not drain the vehicle. Specialty LDOs from manufacturers like Richtek, Torex, or Microchip use 2-character family codes (like "XF") followed by date/lot codes (like "31"). 2. High-Voltage Overvoltage Protection / TVS Diode Array Vehicle electrical systems are notoriously noisy and prone to massive voltage spikes (load dumps) that can immediately fry small electronics. Why it fits: "XF" is a widely utilized SMD code for Transient Voltage Suppressors (TVS) and high-power Zener diodes (such as variants from Vishay or Diodes Inc.). If this component is located right next to the positive wire input terminal, its exact job is to absorb voltage spikes and protect the internal components."

Sprite_tm

I second (third, fourth?) accelerometer. Looking for accelerometers with 12 pins on LCSC brings up the ROHM KX022-1020 and the SENSORTEK STK8321 (where the latter possibly is a clone of the former?) Both have similar packages, and the pinout of both match up with the signal/ground/power connections as seen on the PCB. (With one exception: both need a connection to pin 10, and on the PCB I'm not seeing that, but perhaps there is a via hidden under the package?) You could probably check if it's an accelerometer by scoping out pin 1 and seeing if the signal changes if you tap the board.

Stuart-AJC

Gemini says: Based on the marking XF on a SOT-23 package, this component is very likely a Nexperia (formerly NXP) PMV65XP P-channel MOSFET.

Slymouse

The Gemini results being all over the place is revealing of the limitations at times of ai.

Slymouse

Can we power it on and see if a wifi or Bluetooth device comes up? The info in that could help

Drew Macrae

I like this guess, maybe they authenticate the device to the software so they don’t end up supporting competitor’s hardware.

cyanic

Where does one find LGA12 EEPROMs? I see a few QFN12 but that's not the same footprint.

Drew Macrae

Does the onboard EEPROM have self-write capability on all revisions of the IC? …I’m still bitter about two specific times it didn’t and my board/BOM didn’t have space.

Bob Carter

SPI RAM ? for long term logging

Peter Membrey

Gave GPT 5.5 Pro a go at it and told it to justify its position: The chip marked XF / E1 is almost certainly a 3-axis MEMS accelerometer, most likely a LIS2DH12-compatible 2×2 mm LGA-12 digital accelerometer rather than a regulator, flash chip, RF part, or EEPROM. I would keep the exact vendor as tentative from the photo alone, but the functional identification is strong. Why: 1. The silkscreen gives it away. Immediately next to the chip there is an X/Y/Z axis orientation marking on the PCB. Designers put that beside accelerometers/IMUs so firmware and mechanical orientation can be matched. 2. The package matches. The device is a tiny square LGA-style part with edge pads and a pin-1 dot, very consistent with small MEMS accelerometers. ST’s LIS2DH12, for example, is a 3-axis digital accelerometer in an LGA-12 2.0 × 2.0 × 1.0 mm package with I²C/SPI output. 3. The board context fits. The main MCU is marked CH582F, a WCH BLE/RISC-V MCU family part with SPI/I²C-style peripheral support, so a small motion sensor connected to it makes sense for a BLE tag/beacon/remote-style board. 4. “XFE1” is not enough on its own. SMD parts often use very short top marks rather than full part numbers, so the marking code alone is ambiguous; package, layout, surrounding silkscreen, and circuit context matter more here. How I’d confirm it electrically: probe the bus from the CH582F. If it is LIS2DH12/LIS3DH/SC7A20-class, you would expect an I²C device around 0x18/0x19, and for LIS2DH12 specifically the WHO_AM_I register at 0x0F returns 0x33. So my identification would be: U? = 3-axis accelerometer, likely LIS2DH12-compatible; exact manufacturer not proven from the XF/E1 top mark alone.

Big Clive

They have been very random guesses.

Stephen Tall

@cyanic I've seen Chinese "domestic" flash in that package, but unmarked & took a lot of working out to realise what it was. Having looked a bit more - I don't see pullups & I don't think the CH582 internal pull ups work in I2C mode, but I could well be wrong.

Mike Holloway

What are the X/Y/Z axis orientation marks?

The Black Chamber

I stand by my above comment. It's probably a voltage regulator.

Tomáš Kováčik

just for BT setup you need something to set BT address at least. few comercial BT modules from china required external eeprom,probably eeprom is waste of space on chip :D

Big Clive

That does tally up with the pinout, with clock and data going to the microcontroller.

Tomáš Kováčik

LIS2DH12 pin4 is digital IO, here it is grounded, pin6 ground, here not connected (ground is going around = not grounded pin)

Stephen Tall

First page on the copy I have says there's data flash & table 2.3.1 gives the address location 0x70000 to 0x77FFF

Tomáš Kováčik

pinout of KX022 is spon on, but why ? to log only while vehicle is moving? that looks like very specific function to be on on bluetooth module, but china ... :))

Mike Page

Apart from the imaginary silk markings, this has credibility. It's surely worth probing either I2C or SPI to test.

Ymir the Frost Giant

I also encountered a mystery chip recently. It was in my kebab.

Michael T

Right size and pin configuration, but on the PCB pins 8 and 9 are tied together. That'd be Vdd and Gnd on a LIS2DH12