Home Creators Posts Import Register Favorites Logout

Content

This is very neat, and I only managed to make a slight whiff of smoke once while probing it.

It's a triac based soft starter for loads like universal motors (the AC motors with brushes). It gently ramps them up to full speed with phase angle control.

The way it powers itself is incredibly clever.

https://www.youtube.com/watch?v=2eqq6pMrXnY

Files

Clever soft-start module for AC power tool motors

Despite them rating this module at 20A I'd suggest using it at much lower current to avoid excessive heat dissipation from the triac. In some applications it will also benefit from having its tab mounted to a heat dissipating surface. When powered up, this unit uses phase angle control to gently ramp the output up over a few seconds. It is aimed at specific loads like power tools with universal motors (the type with carbon brushes). It should not be used with some electronic loads like switching power supplies and some motors. The main advantages of the soft start are reduced peak starting current to avoid nuisance circuit breaker tripping, and also the greatly reduced strain on the mechanical components. Note that there is no RF noise filtering, so some radio noise may occur locally during the initial ramp up. The circuitry is very clever. It uses a microcontroller to drive a triac and uses a simple zero crossing point detection circuit for three functions - triac trigger timing, to reset as soon as the power is removed and also to control a simple resistive dropper so that it is only active for a short part of the sine wave near the zero crossing point. It's possible that adding an external snubber network (100nF capacitor in series with a 100 ohm resistor) may give better protection to the triac. The triac is from the BTA series, so its mounting tab is isolated, but note that some triacs have live heatsink tabs. The suffix B usually indicates gate sensitivity. As usual,, this technical delight came from AliExpress (not a sponsor). Here's an affiliate link to the item. Note that it will probably pop up in a bundle deal. https://s.click.aliexpress.com/e/_c4KNUv5T The price varies wildly between about £1.30 to £3.50, so shop about. If you enjoy my videos, supporting the channel on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

Doug Merrett

Is it leading edge switching? Isn't that less good for classic filament bulbs? If it was trailing edge, it would slowly heat the filament and then turn it off versus hitting it with lots of voltage at the beginning.

Big Clive

It is leading edge, but still gives the lamp a soft start and reduces initial filament shock.

Mike Page

Thanks, Clive. The triac's isolated tab adds significant thermal resistance, but no-one's going to run a 3-6 horse motor off this. Hopefully. And even if they do and smoke the triac, nothing bad happens.

Mike Page

Filament bulbs have a decent time constant. At 50Hz (100Hz RMS power), ripple is maybe 10% of light output. Fluorescent tubes OTOH have a pretty surprising bandwidth. You could transmit data with those.

ola garstad

Turn the schematic upside down with the negative side up. It makes it a lot easier to understand how it works.

Andrew Ellis

Wish it were available for us unfortunates in 117V-land. My guess is that there just isn't enough EMF available to run the circuitry.

Charles

I highly recommend soft-start for tools with powerful motors. When I got a new router (the wood kind, not wifi...) 20 years ago, it had a soft-start circuit built in. It's nice because it's a 2+ horsepower motor, and my old router kicks like a mule every time you turned it on. It's actually a safety improvement because it could buck right out of your hands if you weren't expecting it. Cool circuitry! Thanks for drawing the inverse version, much easier to follow.

Big Clive

I'm not sure how suited to 120V it is. The main factor will be the two current limiting resistors in the power supply. There must be dedicated 120V versions.

Jon Knight

Neat - and a good explanation of a rather complex yet simple circuit. Thanks Clive!