Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

Friends: 

The early part of the week is always a flurry of shooting, editing, and scripting, but I found a second to snap a quick pic of the leg vise that's going to cap off our Joiner's Bench. 

This thing might cost you as little as $43 to build and it's solid as a rock. Best of all, there's no lower-guide and NO PIN to adjust. I really can't imagine a better vise for the money. 

But as always, I'll let you be the judge. I count on my Patrons to give it to me straight. 

New video Saturday!

--Rex

Files

Previews only

Comments

Paul Thoma

Rex, as a lefty, should I reverse this to the opposite (right hand) corner of the bench?

Csongor Halmai

I am not Rex but I think you should. :) I am left-handed and I can imagine that I fix a piece of timber into this leg vise, I turn my right-hand side to the table and use a plane in my right hand to work on the timber. If the vise was on the other side, it would be very inconvenient for me so I think you feel the same when it is on the "wrong" side for you.

Infidel305

as a lefty i say without a doubt yes unless you like awkward angles or working from off the end of the bench.

Jake Cotumaccio

Not sure if you've seen his post, but this is basically the same setup that Jay Bates uses for his leg vise. Between the Yost vise and the wedge at the bottom, I think it's the most effective, cost-efficient design. I was considering this design before but you definitely made my decision a lot easier (as opposed to saving up for the $400 Benchcrafted hardware by skipping groceries for a month). Edit: Here's a pic of his https://jayscustomcreations.com/wp-content/uploads/2018/02/hickory-leg-vise-42.jpg

Rex Krueger

Jay's build is absolutely an inspiration and he'll get a shout-out in the video. Mine is different in a few ways: 1. Angled 2.) Built entirely with hand tools and 3) I found a cheap and ultra-stiff source for wood. Jay says his vise flexes a bit. Mine doesn't. Also, $400 for a vise is insanity. I build the entire bench and outfitted it with holdfasts and a vise for UNDER $250.

Jake Cotumaccio

Interesting, I couldn't tell if it was made from laminated 2x4s or something else, but I can't imagine that white pine would be stiff enough though. Yeah I noticed that angle, I'm curious what that's going to look like. And sure it would be nice to have a jointer, planer, table saw, router table, and drill press, but I'm sure you've got plenty of tricks to make it work with hand tools. Looking forward to the video!

Kevin Lundquist

Very cool! I wish I could keep up with you; I'm not even done with the trestles yet.

Alexander Charonitakis

Yooohhhooooo!!! Nice... As a lefty though I will install it on the other end of the bench!!!

tom Masters

It would be cool to be able to move the vise around the bench.

William Allen

You can, easily, just mount the bench side thread on all four corners, "moveable vise".

William Allen

Almost identical to the leg vise I experimented with. Of all the bench vises, the leg vise is the most versatile and the strongest. Your design is clearly ROCK solid and mega easy to use.

Rick Prosser

I built essentially the same vice a while back, and I ended up adding a 3/4 in pipe guide to keep the bottom from swinging back and forth so much. I used the house jack threads, so yours may work more smoothly with less swinging. Got the idea here - https://www.youtube.com/watch?v=aI0sZodYJrI&t=10s I did not use the pipe clamp spacer - just the pipe guide with the angle floor board.

Rex Krueger

Well, since this is my full-time job, I move pretty fast. You don't need to keep up. You gotta move at your speed.

Rex Krueger

That's a great point, although I've always been more or less happy with my vise in one spot. I've never really thought about moving it.

Kevin Lundquist

As you said, it's hard to make a workbench without a workbench. I'm having trouble holding the 2x4s steady while cutting the half-lap joints. I'm thinking of screwing them to the tree in my front yard while I cut them. Update: 1 trestle is done. I wound up clamping the 2x4s to the handrail of the steps going up into the house from my garage. The step and riser made a nice backstop. Then I used my sawsall to make the longitudinal rip cut. This was probably better than my other idea, which was to strap the 2x4s to my car ramps and park the car on the end of the boards to hold them down :-) Hoping to finish the book case I want to build before the heat-death of the universe.

Drew Nelson

Looking forward to seeing the video Saturday!

Chris Donovan

Please make payments due on the first of the month.

carlo pieracci

leg vises were seen on ancient Nicholson benches: probably it offers more gripping surface, is pretty and affordable. I think its simpler to install than a face vise. How does it work without a guide and a pin?

Jac

After your last video I actually thought to myself, "Ooh, I hope it's gonna be an angled leg vise." And here it is! I am super psyched for the build video.

Mike J

Got a link FROM THE FUTURE to the video here on Patreon, but am getting a 404. It's signed "Happy Saturday -Rex". Apparently that bench interacts with the quantum realm, can't wait to make it!

Garrett C.

Beautiful in form and function! You’re really good at making me feel able to tackle stuff like this... even if there is a little dunning-Krueger effect that gives me some initial overconfidence... I feel like I can try