Converted cars, checked against AC1: EvoForge 1.1.47 (Patreon)
Content
Thank you for supporting EvoForge! 1.1.47 comes from testing converted cars in the game, next to AC1 on the same PC: every problem found is fixed as a rule for every converted car, and more of what AC1 and CSP mods contain now reaches EVO. The track builder gets US maps, a repaired horizon, scenery up to 8 km around an area, a picture for every track, a pit lane gap and easier object editing. Convert your cars and tracks again to get the fixes.
Converted cars: fixes seen in the game
A third spring on one axle only closed the game while loading: EVO always reads one per axle. The other axle now gets a neutral third spring, with no force, as AC1 behaves, and the report says so.
Screen values anchored on hidden cockpit parts lying on a screen are shown again on that screen, unless it sits on the steering wheel. 4 cars of the 197 in our test set change, each towards its real screen.
Rear-view camera screens, and central mirrors whose view is blocked by the car, film the track behind: when the car hides 90 % or more of the view, the camera moves back along its line of sight until it is clear, with AC1’s direction and field of view.
Shift lights on a screen the conversion builds light up; they had nothing to show on (6 cars of 197). Backlit dials and steering-wheel icons light only their markings, not the whole plate (13 cars of 190).
Tyre pressures with no declared decimals show none, as in AC1: 26, not 26.0.
A conversion no longer stops on its own while waiting on the network, and gear files AC1 never reads are no longer counted in the import preview.
Converted cars: closer to AC1
Engine braking starts at idle, as in AC1, instead of adding 7 to 38 N·m near idle. Measured next to AC1, engine released in neutral: within 7 %.
Traction control: three settings left from the template car now take the values EVO’s own cars use.
A third spring (heave) that AC1 lets you adjust is adjustable in EVO’s setup screen, with the mod’s ranges and the car’s own starting value. Its bump stops, progressive rate and packers have no equivalent and are listed in the report.
Anti-roll bars that CSP defines as a list of steps become steps in the setup, the way EVO’s own cars do it. Engine maps written the same way are not carried over, and the report says so.
Cars written for CSP’s extended physics: hot pressure, wear tied to load and grip after the peak follow CSP’s rules, the ones these mods were tuned with. The tyre heating calibration of every car now uses the right pressure gain.
Hybrids whose MGU-H only recharges the battery now recharge it.
The starter motor is 30 N·m, the value most of EVO’s own engines use.
Converted cars: what you see, and the report
Parts declared loose in AC1’s damage file (bumpers, bonnet, wing) move after an impact through EVO’s own damage system; their wobble is not carried over. The three loose parts every conversion had inherited from the template car are gone.
The shadow under the car is drawn from the mod’s own shadow picture. On cars with two wipers, both blades wipe.
Screens: more than two per car, AC1’s screen item settings (refresh rate, G-forces, delta bars, gear pictures), CSP odometers and trip counters in the mod’s format, battery bars that follow the charge.
A windscreen sun strip casts its shadow with CSP’s threshold.
Each livery keeps its race number in the game’s Car No., and the driver’s suit, gloves and helmet of each livery, taken from your own AC1 install.
Flames are sized by AC1’s own rule; blue flames stay orange in EVO.
The conversion report tells the truth: no more “not carried over” for tyre wear curves and aero controllers that are, nor “not implemented” for flames. And what EVO cannot do is written instead of dropped: shaking exhausts and window nets, exhaust smoke and sparks, a throttle response that opens more at high revs, an adjustable centre differential preload, raised number plates, blue flames, the navigation map and car radio.
Converted tracks
Plants no longer float in the air: an almost fully transparent cut-out surface, such as a sheet carrying tree shadows, is no longer taken for ground.
A grass layer no longer pushes the trees out: places are reserved family by family, tree against tree (about twice the trees on the track where it was reported).
Tall grass becomes EVO’s tall grass instead of bushes, and is left out where the track’s official CSP config replaces it with GrassFX, as in AC1 with CSP.
Variables in official CSP configs are now replaced, so the sections that use them work again (rain puddles, for instance).
Tracks with several layouts: every layout counts as track, so no grass grows across the others; a pit lane that crosses the start line keeps its crossing, so the AI leaves the pits; pit lanes get no dirt, as on EVO’s own tracks. TV cameras on one layout only mean a conversion from before 1.1.44: convert it again.
Track builder
US state maps download (they were refused). Near a state border, states are combined instead of offering a 1.8 or 4.2 GB region.
The map offer shows where you are working, with Download ready, and gives its size in under half a second.
The horizon of every import had been flat since 27 October: the far relief came out empty and the valley’s photo was draped on a wall. Fixed, and repaired at your next Build, without importing again.
Scenery around an area, chosen at import: Normal 3.2 km, Large 5.6 km or Very large 8 km of relief and satellite photo on each side. In France the far relief no longer comes out in steps.
Ground under a bridge stays below the deck: no more mound of earth at the start of a bridge. Junctions on a slope are smoother.
Every built track gets its picture (the Photo button picks the viewpoint), and a free-roam area’s map shows its streets.
Pit lane gap, 0 to 30 m: a strip of grass between the track and the pit lane, entry and exit crossing it at an angle; where room runs out, the gap narrows and the editor says so.
Objects: picked by their whole box, turned to the degree, laid Along a curved path with a spacing, with one line of help per placing mode, and raised or lowered, like trees and buildings. The start line no longer follows the pits by default.
These track builder changes have been checked in the editor, not driven in game yet.
Known issues
A quick race with more cars than the track has grid slots closes the game: keep the number of cars, you included, within the grid until it is handled.
On a track with several layouts, AI cars stuck after their first pit stop: not explained yet.
Shift lights on a screen the conversion builds light up as one band per group; a very intense backlit colour can come out tinted; hybrids recharge less under braking than in AC1; some screens number the ABS and TC positions differently from AC1.
Feedback is welcome on the Discord: https://discord.gg/x3w7eCDFkK