Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Content

My re-flashed with Repetier (aka Leonardo) DaVinci 1.0A is back up and running. It had a broken connection in the hotend wiring that I could not find and I had no time to rewire it. I originally thought it was just another bad connector, which is typical on these machines, but that didn't seem to fix it. The printer would work fine for about 20 layers and then the temp on the hotend would start to drop until it was printing with air. 

I probed and measured and finally let it collect dust while it went on to other things. Recently I fixed my Fabrikator Mini that had a loose gear on the X-Axis and that inspired me to tear down the Leonardo. After a lot of probing I found an intermittent connection inside the insulation. The wiring in these printers is marginal at best and this one has had it's X-Axis stepper wiring repaired twice. I fixed the connection but still found the heat going in and out. That's when I decided to check the connector again. Roy Olmstead (Patreon Supporter) had commented to me many times that even the newer white connector had issues. He was right. I cut apart the connector and made a more solid connection (I will solder it later). This fixed the problem and the printer is back in action. Two bad connections in one wire.


I have to admit, I missed this printer a bit. The FlashForge Dreamer and Fabrikator Mini are my goto printers. The MAKERFRONT is still right up there but the fire I had on it now makes me have to check on it many times and I won't print overnight with it. So the MAKERFRONT and the issues I've had with the ROBO3D left me wanting a larger printer for ABS I could rely on. The Leonardo fit that job quite nicely before the wiring issued appeared. I've already printed a few things on it, since the repair, and it seems to be running well. It's not the best quality of the bunch but acceptable for many prints. And once I get it fully dialed in, the enclosed case will help make an acceptable large ABS printer to use when the Dreamer is being used or the design is just too big.


I really want to get down to no more than 5 printers or less. I can't keep them in tune or in use enough beyond that count. The only exception is a printer that is producing a product that sells in which case it will be in the corner printing money (as I like to look at it). My original DaVinci 1.0 is doing that now. It's logged over 3000 hours of continuous printing of one design and it's paid for itself twice so far with that print that I sell through a partner. My second Stock DaVinci 1.0 wore out the idler gear printing for money but that design has been phased out. I've decided to make that into a Leonardo as well but with a better hotend. That will be a multiple part series of videos. 


The Jr. is now supported by Simplify3D. I tried it and didn't see a big difference in quality but the slicing time is a huge improvement over XYZware. I can now control every printer I have with S3D. The Jr is getting less and less use lately though I have a print I'm considering for sale that may be perfect for the Jr. so it may become a money machine soon. Jr. only cost me $183 so it should pay for itself in short order (hopefully).


So DaVinci's are making a comeback on my channel. They got me started in 3D printing and converting them to Leonardo's helps make them worth keeping. Many people have asked to see more of them on the channel so I've listened and I'll be showing them more. I still think the company support sucks but since there are so many of these machines around, I think it's time I did more to show people what to do with an old 1.0 and make it useful again.

Files

Previews only

Comments

Anonymous

I had a printer like that, had a shit connector AND a broken wire within the insulation that would arc occasionally.. just crap cheap wires.

Anonymous

Great to hear. Haven't used my stock DaVinci 1.0 for a while and I'd like to get it going again with Repetier. Can a DaVinci with Repetier (or other firmware) do a real auto level? I would think it might be possible using the stock sensor. Look forward to following your project.

elproducts

Auto level is in the Repetier software but I've never used it. I'll have to try that at some point but I haven't had much luck with auto-level. I prefer to just manually adjust during the first layer.