November Release - SSR2 Alpha (part 2) (Patreon)
Downloads
Content
Hi guys,
SSR2 Alpha is ready. All of the STLs are on the (part 1) post. With this (part 2) post you should now have everything you need to complete a working alpha build. I will of course be following up with a detailed livestream on the device electronics and setup, but in the meantime you can check out last week's livestream for an overview.
Livestream link here.
I have some small improvements I want to make to the device and to the firmware code over the next few weeks and months, likewise I'm going to expand and consolidate the assembly notes, but substantially this is a complete new device. I am really looking forward to hearing your feedback.
Remember that the #maker-chat channel on the Tempest Discord server is the place to be to ask any question and get help if you run into trouble. Or if I've forgotten to explain something.
Electronics assembly notes:
Consult the SSR2 wiring diagram for the specific connections.
The ESP32 is held in place by 2x M2.5x5mm bolts. I highly recommend using 1x15 dupont connector housing when hooking the wires up to the ESP32. Trust me this will make your life infinitely easier if you ever need to re-connect anything in future.
Use the JST-SH 6-wire leads that come with the GM3506 motors to hook them up to the ESP32. For this I found it useful to remove and re-insert the 6 cables from the plastic connector and re-insert them in the following order: black, red, yellow, white, green, blue-grey (right-to-left when viewed from the chip side of the encoder with the wires coming toward you). I found that flipping the encoders around inside the housing so that the 6-pin connector, instead of the 3-pin connector, faces the hole made things easier.
The supplied wires will have a JST connector on each end, so you will need to cut one end off and crimp on 0.1” female connectors on instead. Apart from the “CSn” blue-grey wires, which each go to separate pins on the ESP32, the wires should be crimped in pairs, ie the two black wires share a connector, the two red wires share a connector, etc.
As with SSR1 I have used a USB-C trigger module for power. This is a 12v module however, not the 20v one used for SSR1. This means you can use a laptop power supply to power this device. There would be nothing to stop you using any other kind of 12v power supply you like of course. If there’s demand I can create a version with an XT60 socket.
The USB-C trigger is held in place by a single M2x8mm bolt, which clamps onto the board. This is positioned off to one side so that it only touches the ground terminal.
SSR2 uses two of the same SimpleFOC mini v1 motor controller boards that are used on SSR1, mounted using M2x6mm bolts. These will be familiar to you if you’ve build an SSR1 and should be treated in the same way. They should receive 12v power from the USB-C trigger. They should be hooked up to the ESP32 using 4 jumper wires each, and each has a 3-wire connection to its corresponding motor. The two boards are grounded to each other via the power supply, but at least one of them must be connected to ground on the ESP32.
The cooling fan is a 40x40mm type arranged to blow air upwards, directed toward the motors by the fan cover. Either a 5v fan, powered off the “Vin” pin on the ESP32, or a 12v fan, powered off the USB-C trigger, can be used. The fan is mounted using 4x M3x20mm bolts and M3 nuts. The fan cover is fixed using 2x M3x8 bolts.
The Motor frame cover is screwed down using 2x M3x8 countersunk bolts.
(The files are protected with the november password because of an ongoing Patreon security flaw. Check your email. Check your Spam Folder. As a $8 or $16 patron you should have received the passwords in your welcome email, but feel free to contact me if you have any trouble finding them. The files are also available on my discord server.)