Home Creators Posts Import Register Favorites Logout
haven't archived this post yet. have a subscription? use the importer!

Downloads

  • Clickspring Hand Vise Inch - Part 4.PDF
  • Clickspring Hand Vise Metric - Part 4.PDF

Missing 1 full-res photo, 2 files, as this post has not yet been imported.

Content

The latest installment of the Hand Vise project - Enjoy!


 

-------------- Video Notes: --------------- 

Tools & Products:

"Solidworks 2013 Bible": http://amzn.to/2FObS1D

"Machinery's handbook": http://amzn.to/2pi7XE5

Sherline Lathe: http://amzn.to/2pnXM19

Sherline WW collets: http://amzn.to/2FYZ7F8

Heavy Duty Arbor Press: http://amzn.to/2G4gog7

Interapid Dial Test Indicator: http://amzn.to/2FPInwH

Super Pike Saw Blades Size 4/0 pkg of 144: http://amzn.to/2tYjKMA

Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): http://amzn.to/2HGPaJJ

Kaowool 24" X 12" X 1" 2400 F Ceramic Fiber Insulation: http://amzn.to/2pfsM3d

Files

Previews only

Wedge Style Hand Vise - Part 4

Wedge Style Hand Vise, Part 4, by Clickspring. In this video, I make the parts that I think give the tool a lot of its visual character - the jaws. ________________________________________________________ A very special thank you to Patrons Dan Keen, Samuel Irons and Sean Kuyper. ________________________________________________________ Abbreviated Transcript: 0:00:04 They consist of an end piece that forms the vise grip, and the main jaw arms, that'll be the focus of this video. The jaw arms need two holes for the pivot screws, as well as a set of holes for the brass rivets which I'll form in the final episode, at the same time as I make the jaw ends. 00:28 Starting with the raw stock, I'm using a printed template to simplify the task of bringing the workpiece to the line. Its a simple method that gives both the perimeter and the hole positions with a fair degree of accuracy, and it removes the difficulty of laying out the design on a small piece of stock. 00:47 Now If a good oil based glue is used, the grip on the part is usually strong enough to see the template stay in place all through the forming process, although even an oil based glue will eventually lift off the surface if it experiences too much heat. So when shaping the perimeter with something like a belt sander, I've found that its important to not let the work get too hot. 01:10 With the template firmly in place, I can drop in those pivot holes, using a wiggler to pick up the hole positions. I've drilled the holes undersize, and then followed with a reamer to ensure a good snug fit with the pivots. 01:58 Next I started work on the perimeter, and by the looks of the blade I put the scroll saw away fully tensioned, and the blade has popped as its cooled down. But it's a good excuse for a closer look at the blades that I use on this machine. 02:14 They're an excellent all purpose metal cutting blade for this saw, and are particularly effective at cutting brass. They can easily cut through 5 mm brass sheet without issue, and only really start to struggle as the stock approaches a thickness of about 10mm. 02:29 The frames for the skeleton clock were just under 10mm when paired together to be cut out, and that was slow going, but the scroll saw equipped with these blades was still much more effective than doing it by hand with a jewellers saw or chain drilling. 02:45 Now whilst these blades and the scroll saw handle brass quite well, cutting 5mm tool steel, is another story altogether. The blades will still cut, but its a really slow and tedious process and its not uncommon to go through a few blades as the cut progresses. 03:01 Lubricating the blade can help, but the reality is 5mm tool steel is right at the outer limit of what can reasonably be expected from this combination of machine and blade. OK, so with most of the waste stock cut away, from here on I'd like to have complete symmetry between the parts. 03:20 So I used a little solvent to remove one of the templates, and then a small amount of CA glue to bond the rough blanks together. I'm locating them by the reamed pivot hole, re-using a simple filing button that was made for the skeleton clock project. The super glue will hold them securely together for the rest of the shaping process, and with them paired together, 03:50 I can take care of this straight section on the mill, much faster than by using the scroll saw. With the perimeter now roughly to size, I took care of the rest of the shaping using the belt sander. And you can see what I mean about the heat causing the template to lift. I'm pushing it a bit too hard here, and judging from the color of the oxide, 04:57 Its getting to over 200 degrees Celcius, which is a bit more than the glue can cope with. Usually its easy enough to just let it cool, and put another spot of glue on the part thats lifted. don't want the heat to break the super glue bond just yet. So with the perimeter complete, I can remove the remaining template, and then soak the jaws apart by leaving them immersed in acetone. :05:41 The time taken to dissolve the acetone depends on how much glue was used; in this case it was just over an hour. A closer inspecton shows that all of that surfacing has left a decent burr on the perimeter, so I used this fine oilstone to tidy them up. 05:59 Its less aggressive than using files, and I find that it leaves me with a much more presentable finish. Now I could easily sand off that little bit of oxide caused by overheating the parts, but I think there's something to be said for keeping the grained finish from the raw stock, so instead I'm using a drop of flux, and its gone in a flash. 06:59 A quick cleanup to remove all traces of the flux, and thats the jaws complete for now. In the next and final video of this hand vise series, I'll cover the fabrication of the jaw ends, and I'll also randomly select the lucky patron who gets to keep the tool. Wedge Style Hand Vise, Part 4, by Clickspring.

Comments

Joel

I can't wait to win! :)

Cameron Gunter

You could "randomly" pick me, ya know... if you wanted... just sayin' Really, though, what was/is your resource for telling how hot metal got by the color of its oxide layer? Is there a chart/website/table that you could reference for this? Or is it just something that you (or someone who taught you) learned with experience?

Matthew Dormer

Great work Chris, I’m enjoying this series as much as the clock. I must compliment you on the Piece of Burl that you used for the base of the clock. Beautiful.

Jeff, Practical Renaissance

Stunning work as always, I never realized the metal cutting capabilities of scroll saws!

Matthew Dormer

Hay Jeff, I also did not realise and have been playing with mine cutting different materials. Chris, Thanks for the blade suggestions.

clickspring

Thanks Matthew, I was totally thrilled when I found that bit of wood! I also picked up a piece of similar sized Rib Fruited Mallee which is equally stunning, although a lot lighter so not suited to this project - I have high hopes that it will suit the next project to follow the clock tho...

clickspring

Hey Cameron, here is an online source: <a href="http://www.engineeringtoolbox.com/tempering-colors-steel-d_1530.html" rel="nofollow noopener" target="_blank">http://www.engineeringtoolbox.com/tempering-colors-steel-d_1530.html</a> The first chart is the incandescent colors (for when you are heating prior to quench), and the second one is the chart showing the oxide color/temperature correlation, for when you are heating to temper. The colors are a little off becuase its computer screen colors, but it is a decent starting point. I also highly recommend you pick up this little book: <a href="https://www.amazon.com/Hardening-Tempering-Treatment-Workshop-Practice/dp/0852428375?ie=UTF8&*Version*=1&*entries*=0" rel="nofollow noopener" target="_blank">https://www.amazon.com/Hardening-Tempering-Treatment-Workshop-Practice/dp/0852428375?ie=UTF8&*Version*=1&*entries*=0</a> Its a great little reference book, and has virtually all you need to know on the subject of home shop heat treating, including a chart inside with the color/temperature correlation that is very well matched to true colors, as opposed to the above. Cheers mate :)

John

Seeing these videos makes me want to get a lathe and mill and just make tools for the hell of it.

Tom Colson

More remarkable results using simple tools...and a lot of not-so-simple-to-develop skills!

Damien Miller

Could I ask where you bought your small oilstone? I've not been able to find anything that size at Blackwoods...

Nick Pelissier

Nicely done Chris! I love how clean your shop is. Also I didn't comment on youtube but that piece of burl is gorgeous! It's really cool to see the clock coming together!

Scott Clausen

Another superb and informative video. Thanks also for the url references you left in other comment replies. Looking forward to the last video and the completed piece. Will there be a plan for the piece available later?

Roland Guth

Bonjour et un Grand Merci !! C'est un plaisir de Vous voir !!! Cordialement RG

Paul Busby

another great video Chris. looking forward to the final one.

clickspring

Yes you can d/l the plans associated with each episode from each Patreon post. The plans are the blue links below the main video. Any problems downloading, let me know :)

Everfalling

i miss the radio tuning sound you used to use for the x-ray overlays. this static sound isn't as fun.

Lachlan Lane

Great stuff as always. I know you offer your plans in both metric and imperial, but what do you use for reaming and from where? Imperial chucking reamers seem relatively available from the state (I'm from Melbourne), however metric seems much less common. Is it worth just using imperial and getting my hands in a fractional drill set for holes requiring tolerance? Keep it up!

clickspring

Ha ha! Just giving your ears a break, normal programming shall return in due course! Cheers Mark :)

Nils Rohwer

Fantastic Chris, thank you. Could I ask how the wiggler helps you find center?

clickspring

Hey Lachlan, yes I tend to use Imperial sized reamers simply because as you say they tend to be the easiest to source. There are also many suppliers who still stock imperial rod stock, so it is quite common for me to mix units across a project to make use of the imperial stock as the mating diameter. You won't find a true fractional drill bit set easy to source, but you don't need them. Just get a set of these: <a href="http://uk.rs-online.com/web/p/drill-bit-sets/0511112/" rel="nofollow noopener" target="_blank">http://uk.rs-online.com/web/p/drill-bit-sets/0511112/</a> a set of these: <a href="http://uk.rs-online.com/web/p/drill-bit-sets/0511128/" rel="nofollow noopener" target="_blank">http://uk.rs-online.com/web/p/drill-bit-sets/0511128/</a> and while you're shopping a set of these: <a href="http://www.suttontools.com/products/spotting-drills-120-d176/" rel="nofollow noopener" target="_blank">http://www.suttontools.com/products/spotting-drills-120-d176/</a> and you're covered for 99.9% of your model engineering needs. You will buy the odd larger bit when the project requires it, but I've found it to be rare. Drill undersized as per the print using the nearest metric equivalent, and ream as required. Twist drills are sufficiently innacurate that the metric/imperial difference is irrelevant, and the reamer can easily cope with a slightly greater load if required. As an aside: a set of center drills for making center holes for turning between centers is essential, but that set can also cover you for spotting too if you want - the tip of a center drill is 120 degrees which is the correct geometry for spotting a 118 degree twist drill. Just limit the cut to the very tip, not the full depth - Stefan Gotteswinter did a great video on this recently which was right on the money: <a href="https://www.youtube.com/watch?v=Ot8wPGQW3JI" rel="nofollow noopener" target="_blank">https://www.youtube.com/watch?v=Ot8wPGQW3JI</a>

clickspring

Hey Nils, its a fascinating little trick actually! The wiggler consists of a chucking piece gently clasping a ball with a rod and point. The natural state of the tool when chucked in the spindle is to be off the spindle center, and sticking out at an angle. But by holding an object (stick, pencil, wrench etc) firmly against the rotating rod as it rotates at a modest rpm (1000 rpm), it is possible to knock the end point precisely onto the spindle axis. It works on exactly the same principle as the lathe bump centering tool - <a href="http://www.clickspringprojects.com/bump-lathe-centering-tool.html" rel="nofollow noopener" target="_blank">http://www.clickspringprojects.com/bump-lathe-centering-tool.html</a> The result is that a wildly eccentric tool suddenly becomes a precision reference of the mill/drill spindle. You can now drive it over the workpiece using the XY table and then lower it over your center pop, edge, whatever, to accurately position your spindle.

Ørjan Fredheim

Hi, Chris! Great video as always! Do you have time for sleeping? In a comment above here you mentioned a project after the clock - have you already decided what is next and willing to share? Catch you later :)

John Creasey

Great tip for removing blue oxide with flux. What kind of flux did you use?

PJ

Thank You for all the links below and the patrons asking great questions. Particularly found the Artco site a Bonus, got lots of stuff I've been looking for. Wish they had an india/Arkansas stone assortments though. I have a couple of sets in SiC but would like some finer ones. Also thanks for the Flux tip as John Creasey mentions below, will give it a try. Grins about the static in the overlay! Thanks for all the fun and learning...and your videos still rock. ~PJ

clickspring

Ha ha! Yes I am definitely a bit bleary eyed at the moment! The next long term YT project is well into development. I have the main project and also a related project that will become the next Patron Series project. I hope to be able to synchronise them so that they will run in parallel at the same time. I'm going to keep the details under my hat for a little bit longer, because revealing detail on either one would reveal the other, but I can say that I am incredibly excited about both projects. Patrons will be the first to hear all of the details.

clickspring

Eziweld 801. Its a typical Zinc Chloride based flux so any local equivalent will do the same thing. Cheers mate :)

Jason Hughes

Awesome Chris! Your craftsmanship is stunning.

Andrew Robb

Hi Chris, great video yet again. That drill link is gold, Dormer are the best drills. M A Ford are great too but mate do they cost some coin. Good for countersinks and spot drills but.

Samuel Irons

It would be interesting to see others do a build along with the next projects.

clickspring

Yes love Dormer and the local brand Sutton - I live in hope that Sutton will one day send me a care package packed with HSS end mill goodness... Ah well a bloke can dream :)

Damien Miller

Thanks very much for the reference, I've just ordered a bunch of stones and files from them.

clickspring

Yes Blackwoods are my "go to" supplier for all things Sutton, as well as drill rod/silver steel, and a lot of other sundry stuff - terrific to deal with

Al McKague

Nice work once again. I wouldn't have thought to try the scroll saw on tool steel! I will have to track down some of those blades. Thanks for the tip.

Easton Bednarek

Hi Chris, I love watching your videos. I'm considering making the vise but was wondering if you would release the solidworks part files? This would be a great first project for my almost finished cnc converted pm-25 mini mill. Thanks for the videos!

clickspring

Hey Easton, at this stage no, although its not a lot of work for you to model directly from the plans yourself :)

Easton Bednarek

Thanks anyway i will definitely try and model them my self, learning solidworks when i was 10 was definitely a good idea. My dad has me modeling all of the parts for the mill now. your videos have caused me to want to get a lathe now! I actually need to turn some pulleys for my belt sander i designed.

baker98270

How'd you do that shot at 5:23?

Colin Dick

Thanks for posting. Just tracking down the Stock needed to make one of these

Brendan Gill

which software do you use to do your 3D models? I am looking for an alternitive as i cant afford Rhino3D

clickspring

Hey Brendan, I use Solidworks, but recommend you check out Fusion360 - same parametric modelling capabilities, free for home use.

Robert

I use both and for the hobbyist fusion is great, it does lack some features that I love about solidworks, however that being said fusion actually does a better job at adding threads to parts.

Pedro González

amazing build as all of your work, you have a fan (at least) in the other side of the world dude (the sunny spain ;O) will the 5th part be available soon? You know your videos have some sort of addictive property and make all of us think of buying machines ... and making clocks! 'Muchas gracias' for the great job you do!

clickspring

Hey Pedro, I will be starting on part 5 this weekend, so it should be out in a few weeks. Cheers mate :)

Mehdi Illipour

Hi Chris, I have Sieg mini lathe and I have many problem on my command for its adjusting . It is not solid and robust . is it nature of the machine or I can come with a solution on that problem . Any book or something that can help me .Cheers ,

clickspring

Hey Mehdi, yes its basically the nature of the machines. They are well known to be lacking in rigidity, and the tailstock on mine is particularly weak. Many people go to considerable lengths to improve them, but for the most part I have found that the solution is to accept the machines for what they are. They are a cheap hobby grade machine, but you can still do outstanding work on them if you are careful and work within their limitations.

Mehdi Illipour

Hi Chris, thank you for your comment .

Mehdi Illipour

Hi Chris, I believe that If I make the shape of gibs from diamond to parallelogram by increasing the length of two faces in parallel to each other from 6 mm 6.5mm , my Sieg lathe could be robust somewhat .It really take my time to adjust it each week and I have to do something to make it useable .Please let me know your thought .

clickspring

Hey Mehdi, it can certainly make a small improvement, but I still think acceptance of the limitations is the best way to approach the issue. I would just move on and start making chips :) The truth is that every lathe, from the finest Hardinge down to our frail little Siegs, all of them have limitations. Sooner or later you bump up against those limitations, and have to adjust your work process to accommodate them. Its worth remembering that some of the most gorgeous, and spectacular work ever seen on planet earth has been completed by craftsmen with not much more than a bow, string and 2 pivots. The vast majority of pre 20th century watchwork (A L Breguet for example) was done on rudimentary hand turns - nowhere near as accurate as even our little Siegs.

Anthony Gage

Idea for a project for you mate, Harrisons H4.....

Anthony Gage

so no chance of the game of thrones opening sequence then ......