Home Creators Posts Import Register Favorites Logout

Content

A different style of video. This cheap (compared to pro-gear) moving light is actually surprisingly well built compared to many "pro" units.

Although it has quirks, it is actually very usable in some situations.

If you just want a light to play with and get to understand DMX control, then this could be a good option.

https://youtu.be/g4VhqilSgrw

Files

Disco light teardown - (Mac Aura clone)

I wasn't expecting this light to be so well built. In many ways it puts pro-lights to shame, but as with most lights it has its little quirks. As revealed in the video it has a slightly odd issue with the ballistic curve of the motor drive. If you send a DMX data change that is significant, the unit will rotate to that position quickly, with the usual stepper motor ramp up and down to maintain torque. But if you make a very small change the unit does not seem to fully enter the torgue ramp, and instead crawls slowly to the selected position over a period of time. The circuitry is breathtakingly simple compared to many pro units. It uses the same multi-processor topology, with one master processor delegating tasks like motor control and LED dimming to other processors. The microcontrollers it is using are:- Main brain - Nation N32L406 CBL7 Motor and position monitoring - Nation N32G430 C8L7 LED drive - CW32F030 K8TT The main processor has 256kb (32 kilobyte) local flash memory for settings. The stepper drivers are the vague SA8555 (TI DRV8885?) The RS485 (DMX512) transmitter/receiver is a BL1585B (MAX485?) The LED drivers are vague generic buck regulator chips. The unit uses a power supply supposedly rated 24V at 400W. The light's power data is:- Standby 18.6W Red 33.4W Green 42.4W Blue 43.4W White 44.4W All at full 182W. (Mac Aura is 228W) The light can operate in DMX mode where it receives data from a lighting network, or it can be used in standalone mode, audio sensing mode and possibly with slave and master functionality - although the manual is vague about that. I compared this light to the Martin Lighting MAC Aura, which is a popular moving wash light in the entertainment industry. A real MAC Aura is very expensive, even second hand. It's a useful light, but I'd never buy a heavily used one, as the spares are expensive. If you have a MAC Aura and it is not lighting the white LEDs in test mode, don't panic. There's an annoying software quirk that removes white from the test sequence when the light is set to calibrated colour mode. If you change it to raw colour mode the white should work. This style of light is available from many sources under different brand names. This one came from a local AliExpress warehouse. I'll give you a starter link (affiliate link) but I strongly recommend you shop about, as the price of these lights covers a massive range. https://s.click.aliexpress.com/e/_c2xqEskB Search for a price around £60 to £80. You may find this light pops up in deals, and may also be available from a local warehouse in your country to avoid shipping issues. Supporting the channel with a dollar or two on Patreon helps keep it independent of YouTube's quirks, avoids intrusive mid-video adverts, gives early access, bonus footage and regular quiet Patreon live streams. https://www.patreon.com/bigclive Alternatively, for a single coffee contribution you can use PayPal:- https://www.paypal.com/paypalme/bigclive #ElectronicsCreators

Comments

Charles

Interesting product and great video. The garage part of the video worked just fine (IMHO) - sound was excellent considering you were essentially shooting in a cavern. The white balance was a little warmer than I'd have made it, but that's just a matter of preference.

Big Clive

In both parts of the video I was wearing a wireless microphone. I will adjust the white balance next time. It was set for the bench lighting.

Brian Deschene

Content great as usual. You asked for comments. It seemed the only issue was the change in “studio” is something you will just need to adjust to. I remember your original videos at “the bench” when you had to adapt to logistics like long enough power cords, like this time. No big deal, just adaptations and improvements to make as you go on. Thank you for what you do and what you’ve done for so many years!

RonNona

I personally liked the juxtaposition of switching between bench and garage, it adds to the presentation. It is also nice to see "you" and not just your hands once in a while. You did an awesome job of editing this. I hope it was not an arduous task.

Robert Morley

Did you meter the leds to see if they where a genuine 20w ??

Amro

I have a strange need for one.

Circuitmike

Jeez, you weren't kidding about how cheap these are. There's a listing for TWO of them, with a case, for US$140. Ships from the US, too, so no tariffs. Honestly I'd probably just buy them if I had any place to store them, but I'm overflowing with random crap as it is.

Big Clive

With all colours at full the total LED power is around 163W. So definitely Chinese watts.

Big Clive

There is still minimal editing.

richard ockman

look to be built ok but what causes the continued movement after the release of the control after a pan. The power supply is not fully shielded maybe noise getting into the controls?

Moz in Oz

You're right, that is a most excellent toy. If I had any possible use for it ever I would buy that and the desk just to play with. BUT I am on a less-stuff mission and I will not be tempted. Well, I will not give in to temptation. Must not!

Big Clive

I think it's just a software issue involving the motor speed ramp. For short movements it stays at the slowest movement.

Big Clive

Have fun with it. It can also be manually controlled from the display.

Big Clive

I think the more I use that space, the easier it will get. When changing filming format a lot of tests have to be done beforehand.

Matthew Richardson

I liked the two-space aspect of the video, Audio was fine for me in both situations (Laptop speakers but nice and clear), and I enjoyed seeing you in the video, Clive. I don't watch your livestreams (GMT + 13 so timing isn't great for me) , so it was nice to be reminded you're not a disembodied pair of hands!

Phil Collins

I was concerned for your beard when it started initialising while you were cuddling it!

Craig Childs

The shift from the bench was good, maybe consider a second camera for focussed looks at the kit. RS485 is a common 24v physical layer interface, I have some from my BMS interfacing days, a few protocols use it like KNX, ModBUS TCP. A lot of 24v equipment manufacturers use it for bespoke interfacing for programming or service connection.

Caleb

So I'm curious: you mentioned they cheaped out a bit on the dmx interface, and there's a chance if something goes wrong of sending mains voltage out on the DMX network. How would one mitigate this risk? Let's say I want to add a couple of these to a rig full of expensive fixtures. Do you have any recommendations for gear to isolate the DMX line? And I'm also curious if the pricey professional fixtures typically have isolated DMX ports.

Big Clive

It's fairly standard DMX network circuitry, but the main risk is equipment with low quality power supplies that could potentially energise the low voltage circuitry with respect to ground.